Update 2.0.x

Marlin/Configuration_adv.h

@@ -2315,6 +2315,7 @@
    */
   //#define EVENT_GCODE_TOOLCHANGE_T0 "G28 A\nG1 A0" // Extra G-code to run while executing tool-change command T0
   //#define EVENT_GCODE_TOOLCHANGE_T1 "G1 A10"       // Extra G-code to run while executing tool-change command T1
+  //#define EVENT_GCODE_TOOLCHANGE_ALWAYS_RUN        // Always execute above G-code sequences. Use with caution!
 
   /**
    * Tool Sensors detect when tools have been picked up or dropped.

Marlin/src/inc/Conditionals_adv.h

@@ -132,17 +132,15 @@
 #define HID_E6         6
 #define HID_E7         7
 
-#define ANY_TEMP_SENSOR_IS(n) (n == TEMP_SENSOR_0 || n == TEMP_SENSOR_1 || n == TEMP_SENSOR_2 || n == TEMP_SENSOR_3 \
-  || n == TEMP_SENSOR_4 || n == TEMP_SENSOR_5 || n == TEMP_SENSOR_6 || n == TEMP_SENSOR_7 \
-  || n == TEMP_SENSOR_BED \
-  || n == TEMP_SENSOR_PROBE \
-  || n == TEMP_SENSOR_CHAMBER \
-  || n == TEMP_SENSOR_COOLER \
-  || n == TEMP_SENSOR_REDUNDANT )
-#if ANY_TEMP_SENSOR_IS(1000)
+#define _SENSOR_IS(I,N) || (TEMP_SENSOR_##N == I)
+#define _E_SENSOR_IS(I,N) _SENSOR_IS(N,I)
+#define ANY_THERMISTOR_IS(N) (0 REPEAT2(HOTENDS, _E_SENSOR_IS, N) \
+  _SENSOR_IS(N,BED) _SENSOR_IS(N,PROBE) _SENSOR_IS(N,CHAMBER) \
+  _SENSOR_IS(N,COOLER) _SENSOR_IS(N,BOARD) _SENSOR_IS(N,REDUNDANT) )
+
+#if ANY_THERMISTOR_IS(1000)
   #define HAS_USER_THERMISTORS 1
 #endif
-#undef ANY_TEMP_SENSOR_IS
 
 #if TEMP_SENSOR_REDUNDANT
   #define _HEATER_ID(M) HID_##M

Marlin/src/inc/SanityCheck.h

@@ -2193,68 +2193,12 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
               #elif !PIN_EXISTS(TEMP_7) && !TEMP_SENSOR_7_IS_DUMMY
                 #error "TEMP_7_PIN not defined for this board."
               #endif
-            #elif TEMP_SENSOR_7 != 0
-              #error "TEMP_SENSOR_7 shouldn't be set with only 7 HOTENDS."
-            #endif
-          #elif TEMP_SENSOR_6 != 0
-            #error "TEMP_SENSOR_6 shouldn't be set with only 6 HOTENDS."
-          #elif TEMP_SENSOR_7 != 0
-            #error "TEMP_SENSOR_7 shouldn't be set with only 6 HOTENDS."
-          #endif
-        #elif TEMP_SENSOR_5 != 0
-          #error "TEMP_SENSOR_5 shouldn't be set with only 5 HOTENDS."
-        #elif TEMP_SENSOR_6 != 0
-          #error "TEMP_SENSOR_6 shouldn't be set with only 5 HOTENDS."
-        #elif TEMP_SENSOR_7 != 0
-          #error "TEMP_SENSOR_7 shouldn't be set with only 5 HOTENDS."
-        #endif
-      #elif TEMP_SENSOR_4 != 0
-        #error "TEMP_SENSOR_4 shouldn't be set with only 4 HOTENDS."
-      #elif TEMP_SENSOR_5 != 0
-        #error "TEMP_SENSOR_5 shouldn't be set with only 4 HOTENDS."
-      #elif TEMP_SENSOR_6 != 0
-        #error "TEMP_SENSOR_6 shouldn't be set with only 4 HOTENDS."
-      #elif TEMP_SENSOR_7 != 0
-        #error "TEMP_SENSOR_7 shouldn't be set with only 4 HOTENDS."
-      #endif
-    #elif TEMP_SENSOR_3 != 0
-      #error "TEMP_SENSOR_3 shouldn't be set with only 3 HOTENDS."
-    #elif TEMP_SENSOR_4 != 0
-      #error "TEMP_SENSOR_4 shouldn't be set with only 3 HOTENDS."
-    #elif TEMP_SENSOR_5 != 0
-      #error "TEMP_SENSOR_5 shouldn't be set with only 3 HOTENDS."
-    #elif TEMP_SENSOR_6 != 0
-      #error "TEMP_SENSOR_6 shouldn't be set with only 3 HOTENDS."
-    #elif TEMP_SENSOR_7 != 0
-      #error "TEMP_SENSOR_7 shouldn't be set with only 3 HOTENDS."
-    #endif
-  #elif TEMP_SENSOR_2 != 0
-    #error "TEMP_SENSOR_2 shouldn't be set with only 2 HOTENDS."
-  #elif TEMP_SENSOR_3 != 0
-    #error "TEMP_SENSOR_3 shouldn't be set with only 2 HOTENDS."
-  #elif TEMP_SENSOR_4 != 0
-    #error "TEMP_SENSOR_4 shouldn't be set with only 2 HOTENDS."
-  #elif TEMP_SENSOR_5 != 0
-    #error "TEMP_SENSOR_5 shouldn't be set with only 2 HOTENDS."
-  #elif TEMP_SENSOR_6 != 0
-    #error "TEMP_SENSOR_6 shouldn't be set with only 2 HOTENDS."
-  #elif TEMP_SENSOR_7 != 0
-    #error "TEMP_SENSOR_7 shouldn't be set with only 2 HOTENDS."
-  #endif
-#elif TEMP_SENSOR_1 != 0
-  #error "TEMP_SENSOR_1 shouldn't be set with only 1 HOTEND."
-#elif TEMP_SENSOR_2 != 0
-  #error "TEMP_SENSOR_2 shouldn't be set with only 1 HOTEND."
-#elif TEMP_SENSOR_3 != 0
-  #error "TEMP_SENSOR_3 shouldn't be set with only 1 HOTEND."
-#elif TEMP_SENSOR_4 != 0
-  #error "TEMP_SENSOR_4 shouldn't be set with only 1 HOTEND."
-#elif TEMP_SENSOR_5 != 0
-  #error "TEMP_SENSOR_5 shouldn't be set with only 1 HOTEND."
-#elif TEMP_SENSOR_6 != 0
-  #error "TEMP_SENSOR_6 shouldn't be set with only 1 HOTEND."
-#elif TEMP_SENSOR_7 != 0
-  #error "TEMP_SENSOR_7 shouldn't be set with only 1 HOTEND."
+            #endif // HOTENDS > 7
+          #endif // HOTENDS > 6
+        #endif // HOTENDS > 5
+      #endif // HOTENDS > 4
+    #endif // HOTENDS > 3
+  #endif // HOTENDS > 2
 #endif // HAS_MULTI_HOTEND
 
 /**
@@ -3288,7 +3232,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
 #if HAS_MOTOR_CURRENT_I2C
   #if BOTH(DIGIPOT_MCP4018, DIGIPOT_MCP4451)
     #error "Enable only one of DIGIPOT_MCP4018 or DIGIPOT_MCP4451."
-#elif !MB(MKS_SBASE, AZTEEG_X5_GT, AZTEEG_X5_MINI, AZTEEG_X5_MINI_WIFI) \
+  #elif !MB(MKS_SBASE, AZTEEG_X5_GT, AZTEEG_X5_MINI, AZTEEG_X5_MINI_WIFI) \
     && (!defined(DIGIPOTS_I2C_SDA_X) || !defined(DIGIPOTS_I2C_SDA_Y) || !defined(DIGIPOTS_I2C_SDA_Z) || !defined(DIGIPOTS_I2C_SDA_E0) || !defined(DIGIPOTS_I2C_SDA_E1))
       #error "DIGIPOT_MCP4018/4451 requires DIGIPOTS_I2C_SDA_* pins to be defined."
   #endif

Marlin/src/inc/Warnings.cpp

@@ -35,6 +35,26 @@
   #warning "WARNING! Disable MARLIN_DEV_MODE for the final build!"
 #endif
 
+// Safety Features
+#if DISABLED(USE_WATCHDOG)
+  #warning "Safety Alert! Enable USE_WATCHDOG for the final build!"
+#endif
+#if HAS_HOTEND && DISABLED(THERMAL_PROTECTION_HOTENDS)
+  #warning "Safety Alert! Enable THERMAL_PROTECTION_HOTENDS for the final build!"
+#endif
+#if HAS_HEATED_BED && DISABLED(THERMAL_PROTECTION_BED)
+  #warning "Safety Alert! Enable THERMAL_PROTECTION_BED for the final build!"
+#endif
+#if HAS_HEATED_CHAMBER && DISABLED(THERMAL_PROTECTION_CHAMBER)
+  #warning "Safety Alert! Enable THERMAL_PROTECTION_CHAMBER for the final build!"
+#endif
+#if HAS_COOLER && DISABLED(THERMAL_PROTECTION_COOLER)
+  #warning "Safety Alert! Enable THERMAL_PROTECTION_COOLER for the final build!"
+#endif
+#if ANY_THERMISTOR_IS(998) || ANY_THERMISTOR_IS(999)
+  #warning "Warning! Don't use dummy thermistors (998/999) for final build!"
+#endif
+
 #if NONE(HAS_RESUME_CONTINUE, HOST_PROMPT_SUPPORT)
   #warning "Your Configuration provides no method to acquire user feedback!"
 #endif

Marlin/src/lcd/e3v2/jyersui/dwin.cpp

@@ -419,7 +419,7 @@ void CrealityDWINClass::Draw_Float(float value, uint8_t row, bool selected/*=fal
   if (isnan(value))
     DWIN_Draw_String(true, DWIN_FONT_MENU, Color_White, bColor, xpos - 8, MBASE(row), F(" NaN"));
   else {
-    DWIN_Draw_FloatValue(true, true, 0, DWIN_FONT_MENU, Color_White, bColor, digits - log10(minunit) + 1, log10(minunit), xpos, MBASE(row), (value < 0 ? -value : value) * minunit);
+    DWIN_Draw_FloatValue(true, true, 0, DWIN_FONT_MENU, Color_White, bColor, digits - log10(minunit) + 1, log10(minunit), xpos, MBASE(row), (value < 0 ? -value : value));
     DWIN_Draw_String(true, DWIN_FONT_MENU, Color_White, bColor, xpos - 8, MBASE(row), value < 0 ? F("-") : F(" "));
   }
 }
@@ -855,7 +855,7 @@ void CrealityDWINClass::Draw_Status_Area(bool icons/*=false*/) {
     }
     if (zoffsetvalue != offset) {
       offset = zoffsetvalue;
-      DWIN_Draw_FloatValue(true, true, 0, DWIN_FONT_STAT, GetColor(eeprom_settings.status_area_text, Color_White), Color_Bg_Black, 2, 2, 207, 417, (zoffsetvalue < 0 ? -zoffsetvalue : zoffsetvalue) * 100);
+      DWIN_Draw_FloatValue(true, true, 0, DWIN_FONT_STAT, GetColor(eeprom_settings.status_area_text, Color_White), Color_Bg_Black, 2, 2, 207, 417, (zoffsetvalue < 0 ? -zoffsetvalue : zoffsetvalue));
       DWIN_Draw_String(true, DWIN_FONT_MENU, GetColor(eeprom_settings.status_area_text, Color_White), Color_Bg_Black, 205, 419, zoffsetvalue < 0 ? F("-") : F(" "));
     }
   #endif

Marlin/src/lcd/e3v2/marlinui/lcdprint_dwin.cpp

@@ -16,7 +16,7 @@
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
  *
  */
 

Marlin/src/lcd/e3v2/marlinui/marlinui_dwin.h

@@ -16,7 +16,7 @@
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
  *
  */
 #pragma once

Marlin/src/lcd/e3v2/marlinui/ui_common.cpp

@@ -16,7 +16,7 @@
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
  *
  */
 

Marlin/src/lcd/e3v2/marlinui/ui_status_480x272.cpp

@@ -16,7 +16,7 @@
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
  *
  */
 

Marlin/src/lcd/extui/dgus_reloaded/DGUSDisplay.cpp

@@ -16,7 +16,7 @@
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
  *
  */
 

Marlin/src/lcd/extui/dgus_reloaded/DGUSDisplay.h

@@ -16,7 +16,7 @@
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
  *
  */
 #pragma once

Marlin/src/lcd/extui/dgus_reloaded/DGUSRxHandler.cpp

@@ -16,7 +16,7 @@
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
  *
  */
 

Marlin/src/lcd/extui/dgus_reloaded/DGUSRxHandler.h

@@ -16,7 +16,7 @@
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
  *
  */
 #pragma once

Marlin/src/lcd/extui/dgus_reloaded/DGUSScreenHandler.cpp

@@ -16,7 +16,7 @@
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
  *
  */
 

Marlin/src/lcd/extui/dgus_reloaded/DGUSScreenHandler.h

@@ -16,7 +16,7 @@
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
  *
  */
 #pragma once

Marlin/src/lcd/extui/dgus_reloaded/DGUSSetupHandler.cpp

@@ -16,7 +16,7 @@
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
  *
  */
 

Marlin/src/lcd/extui/dgus_reloaded/DGUSSetupHandler.h

@@ -16,7 +16,7 @@
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
  *
  */
 #pragma once

Marlin/src/lcd/extui/dgus_reloaded/DGUSTxHandler.cpp

@@ -16,7 +16,7 @@
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
  *
  */
 

Marlin/src/lcd/extui/dgus_reloaded/DGUSTxHandler.h

@@ -16,7 +16,7 @@
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
  *
  */
 #pragma once

Marlin/src/lcd/extui/dgus_reloaded/config/DGUS_Addr.h

@@ -16,7 +16,7 @@
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
  *
  */
 #pragma once

Marlin/src/lcd/extui/dgus_reloaded/config/DGUS_Constants.h

@@ -16,7 +16,7 @@
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
  *
  */
 #pragma once

Marlin/src/lcd/extui/dgus_reloaded/config/DGUS_Control.h

@@ -16,7 +16,7 @@
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
  *
  */
 #pragma once

Marlin/src/lcd/extui/dgus_reloaded/config/DGUS_Data.h

@@ -16,7 +16,7 @@
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
  *
  */
 #pragma once

Marlin/src/lcd/extui/dgus_reloaded/config/DGUS_Screen.h

@@ -16,7 +16,7 @@
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
  *
  */
 #pragma once

Marlin/src/lcd/extui/dgus_reloaded/definition/DGUS_ScreenAddrList.cpp

@@ -16,7 +16,7 @@
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
  *
  */
 

Marlin/src/lcd/extui/dgus_reloaded/definition/DGUS_ScreenAddrList.h

@@ -16,7 +16,7 @@
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
  *
  */
 #pragma once

Marlin/src/lcd/extui/dgus_reloaded/definition/DGUS_ScreenSetup.cpp

@@ -16,7 +16,7 @@
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
  *
  */
 

Marlin/src/lcd/extui/dgus_reloaded/definition/DGUS_ScreenSetup.h

@@ -16,7 +16,7 @@
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
  *
  */
 #pragma once

Marlin/src/lcd/extui/dgus_reloaded/definition/DGUS_VP.h

@@ -16,7 +16,7 @@
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
  *
  */
 #pragma once

Marlin/src/lcd/extui/dgus_reloaded/definition/DGUS_VPList.cpp

@@ -16,7 +16,7 @@
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
  *
  */
 

Marlin/src/lcd/extui/dgus_reloaded/definition/DGUS_VPList.h

@@ -16,7 +16,7 @@
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
  *
  */
 #pragma once

Marlin/src/lcd/extui/dgus_reloaded/dgus_reloaded_extui.cpp

@@ -16,7 +16,7 @@
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
  *
  */
 

Marlin/src/module/temperature.cpp

@@ -2207,22 +2207,22 @@ void Temperature::init() {
 
   // Thermistor activation by MCU pin
   #if PIN_EXISTS(TEMP_0_TR_ENABLE)
-    OUT_WRITE(TEMP_0_TR_ENABLE_PIN,
+    OUT_WRITE(TEMP_0_TR_ENABLE_PIN, (
       #if TEMP_SENSOR_IS_ANY_MAX_TC(0)
-        1
+        HIGH
       #else
-        0
+        LOW
       #endif
-    );
+    ));
   #endif
   #if PIN_EXISTS(TEMP_1_TR_ENABLE)
-    OUT_WRITE(TEMP_1_TR_ENABLE_PIN,
+    OUT_WRITE(TEMP_1_TR_ENABLE_PIN, (
       #if TEMP_SENSOR_IS_ANY_MAX_TC(1)
-        1
+        HIGH
       #else
-        0
+        LOW
       #endif
-    );
+    ));
   #endif
 
   #if HAS_HEATER_0

Marlin/src/module/thermistor/thermistors.h

@@ -42,18 +42,6 @@
 #define OV_SCALE(N) (N)
 #define OV(N) int16_t(OV_SCALE(N) * (OVERSAMPLENR) * (THERMISTOR_TABLE_SCALE))
 
-#define TEMP_SENSOR_IS(n,H) (n == TEMP_SENSOR_##H)
-#define ANY_THERMISTOR_IS(n) ( TEMP_SENSOR_IS(n, 0) || TEMP_SENSOR_IS(n, 1) \
-                            || TEMP_SENSOR_IS(n, 2) || TEMP_SENSOR_IS(n, 3) \
-                            || TEMP_SENSOR_IS(n, 4) || TEMP_SENSOR_IS(n, 5) \
-                            || TEMP_SENSOR_IS(n, 6) || TEMP_SENSOR_IS(n, 7) \
-                            || TEMP_SENSOR_IS(n, BED) \
-                            || TEMP_SENSOR_IS(n, CHAMBER) \
-                            || TEMP_SENSOR_IS(n, COOLER) \
-                            || TEMP_SENSOR_IS(n, PROBE) \
-                            || TEMP_SENSOR_IS(n, BOARD) \
-                            || TEMP_SENSOR_IS(n, REDUNDANT) )
-
 typedef struct { int16_t value; celsius_t celsius; } temp_entry_t;
 
 // Pt1000 and Pt100 handling

Marlin/src/module/tool_change.cpp

@@ -954,7 +954,7 @@ void fast_line_to_current(const AxisEnum fr_axis) { _line_to_current(fr_axis, 0.
           #if ENABLED(TOOLCHANGE_NO_RETURN)
             const float temp = destination.z;
             destination = current_position;
-            destination.z = temp.z;
+            destination.z = temp;
           #endif
           prepare_internal_move_to_destination(TERN(TOOLCHANGE_NO_RETURN, planner.settings.max_feedrate_mm_s[Z_AXIS], MMM_TO_MMS(TOOLCHANGE_PARK_XY_FEEDRATE)));
         }
@@ -1307,7 +1307,7 @@ void tool_change(const uint8_t new_tool, bool no_move/*=false*/) {
 
     TERN_(HAS_FANMUX, fanmux_switch(active_extruder));
 
-    if (!no_move) {
+    if (ENABLED(EVENT_GCODE_TOOLCHANGE_ALWAYS_RUN) || !no_move) {
       #ifdef EVENT_GCODE_TOOLCHANGE_T0
         if (new_tool == 0)
           gcode.process_subcommands_now_P(PSTR(EVENT_GCODE_TOOLCHANGE_T0));

Marlin/src/pins/lpc1769/pins_BTT_SKR_V1_4_TURBO.h

@@ -31,4 +31,4 @@
 // Include SKR 1.4 pins
 //
 #define REQUIRE_LPC1769
-#include "../lpc1768/pins_BTT_SKR_V1_4.h"
+#include "../lpc1768/pins_BTT_SKR_V1_4.h" // ... BTT_SKR_common

Marlin/src/pins/pinsDebug_list.h

@@ -26,9 +26,9 @@
 // If the new pin name is over 28 characters long then pinsDebug.h will need to be modified.
 
 #if TARGET_LPC1768
-  #define ANALOG_OK(PN) ((PN) == P0_02 || (PN) == P0_03 || (PN) == P0_23 || (PN) == P0_24 || (PN) == P0_25 || (PN) == P0_26 || (PN) == P1_30 || (PN) == P1_31)
+  #define ANALOG_OK(PN) (WITHIN(PN, P0_02, P0_03) || WITHIN(PN, P0_23, P0_26) || WITHIN(PN, P1_30, P1_31))
 #else
-  #define ANALOG_OK(PN) ((PN) >= 0 && (PN) < NUM_ANALOG_INPUTS)
+  #define ANALOG_OK(PN) WITHIN(PN, 0, NUM_ANALOG_INPUTS - 1)
 #endif
 
 #line 35 // set __LINE__ to a known value for both passes
@@ -37,86 +37,130 @@
 // Analog Pin Assignments
 //
 
-#if defined(EXT_AUX_A0) && ANALOG_OK(EXT_AUX_A0)
+#define _EXISTS(PN,V...) (defined(PN##V) && PN##V >= 0)
+
+#if _EXISTS(EXT_AUX_A0)
+  #if ANALOG_OK(EXT_AUX_A0)
   REPORT_NAME_ANALOG(__LINE__, EXT_AUX_A0)
 #endif
-#if defined(EXT_AUX_A1) && ANALOG_OK(EXT_AUX_A0)
-  REPORT_NAME_ANALOG(__LINE__, EXT_AUX_A1)
 #endif
-#if defined(EXT_AUX_A2) && ANALOG_OK(EXT_AUX_A0)
-  REPORT_NAME_ANALOG(__LINE__, EXT_AUX_A2)
+#if _EXISTS(EXT_AUX_A1)
+  #if ANALOG_OK(EXT_AUX_A0)
+    REPORT_NAME_ANALOG(__LINE__, EXT_AUX_A0)
+  #endif
 #endif
-#if defined(EXT_AUX_A3) && ANALOG_OK(EXT_AUX_A0)
-  REPORT_NAME_ANALOG(__LINE__, EXT_AUX_A3)
+#if _EXISTS(EXT_AUX_A2)
+  #if ANALOG_OK(EXT_AUX_A0)
+    REPORT_NAME_ANALOG(__LINE__, EXT_AUX_A0)
+  #endif
+#endif
+#if _EXISTS(EXT_AUX_A3)
+  #if ANALOG_OK(EXT_AUX_A0)
+    REPORT_NAME_ANALOG(__LINE__, EXT_AUX_A0)
+  #endif
 #endif
-#if defined(EXT_AUX_A4) && ANALOG_OK(EXT_AUX_A0)
-  REPORT_NAME_ANALOG(__LINE__, EXT_AUX_A4)
+#if _EXISTS(EXT_AUX_A4)
+  #if ANALOG_OK(EXT_AUX_A0)
+    REPORT_NAME_ANALOG(__LINE__, EXT_AUX_A0)
+  #endif
 #endif
-#if PIN_EXISTS(FILWIDTH) && ANALOG_OK(FILWIDTH_PIN)
-  REPORT_NAME_ANALOG(__LINE__, FILWIDTH_PIN)
+#if PIN_EXISTS(FILWIDTH)
+  #if ANALOG_OK(FILWIDTH_PIN)
+    REPORT_NAME_ANALOG(__LINE__, FILWIDTH_PIN)
+  #endif
 #endif
-#if PIN_EXISTS(MAIN_VOLTAGE_MEASURE) && ANALOG_OK(MAIN_VOLTAGE_MEASURE_PIN)
-  REPORT_NAME_ANALOG(__LINE__, MAIN_VOLTAGE_MEASURE_PIN)
+#if PIN_EXISTS(MAIN_VOLTAGE_MEASURE)
+  #if ANALOG_OK(MAIN_VOLTAGE_MEASURE_PIN)
+    REPORT_NAME_ANALOG(__LINE__, MAIN_VOLTAGE_MEASURE_PIN)
+  #endif
 #endif
 #if !defined(ARDUINO_ARCH_SAM) && !defined(ARDUINO_ARCH_SAMD)  // TC1 & TC2 are macros in the SAM/SAMD tool chain
-  #if defined(TC1) && ANALOG_OK(TC1)
+  #if _EXISTS(TC1)
+    #if ANALOG_OK(TC1)
     REPORT_NAME_ANALOG(__LINE__, TC1)
   #endif
-  #if defined(TC2) && ANALOG_OK(TC1)
-    REPORT_NAME_ANALOG(__LINE__, TC2)
+  #endif
+  #if _EXISTS(TC2)
+    #if ANALOG_OK(TC1)
+      REPORT_NAME_ANALOG(__LINE__, TC1)
+    #endif
   #endif
 #endif
-#if PIN_EXISTS(TEMP_0) && ANALOG_OK(TEMP_0_PIN)
-  REPORT_NAME_ANALOG(__LINE__, TEMP_0_PIN)
+#if PIN_EXISTS(TEMP_0)
+  #if ANALOG_OK(TEMP_0_PIN)
+      REPORT_NAME_ANALOG(__LINE__, TEMP_0_PIN)
+    #endif
 #endif
-#if PIN_EXISTS(TEMP_1) && ANALOG_OK(TEMP_1_PIN)
-  REPORT_NAME_ANALOG(__LINE__, TEMP_1_PIN)
+#if PIN_EXISTS(TEMP_1)
+  #if ANALOG_OK(TEMP_1_PIN)
+    REPORT_NAME_ANALOG(__LINE__, TEMP_1_PIN)
+  #endif
 #endif
-#if PIN_EXISTS(TEMP_2) && ANALOG_OK(TEMP_2_PIN)
-  REPORT_NAME_ANALOG(__LINE__, TEMP_2_PIN)
+#if PIN_EXISTS(TEMP_2)
+  #if ANALOG_OK(TEMP_2_PIN)
+    REPORT_NAME_ANALOG(__LINE__, TEMP_2_PIN)
+  #endif
 #endif
-#if PIN_EXISTS(TEMP_3) && ANALOG_OK(TEMP_3_PIN)
-  REPORT_NAME_ANALOG(__LINE__, TEMP_3_PIN)
+#if PIN_EXISTS(TEMP_3)
+  #if ANALOG_OK(TEMP_3_PIN)
+    REPORT_NAME_ANALOG(__LINE__, TEMP_3_PIN)
+  #endif
 #endif
-#if PIN_EXISTS(TEMP_4) && ANALOG_OK(TEMP_4_PIN)
-  REPORT_NAME_ANALOG(__LINE__, TEMP_4_PIN)
+#if PIN_EXISTS(TEMP_4)
+  #if ANALOG_OK(TEMP_4_PIN)
+    REPORT_NAME_ANALOG(__LINE__, TEMP_4_PIN)
+  #endif
 #endif
-#if PIN_EXISTS(TEMP_5) && ANALOG_OK(TEMP_5_PIN)
-  REPORT_NAME_ANALOG(__LINE__, TEMP_5_PIN)
+#if PIN_EXISTS(TEMP_5)
+  #if ANALOG_OK(TEMP_5_PIN)
+    REPORT_NAME_ANALOG(__LINE__, TEMP_5_PIN)
+  #endif
 #endif
-#if PIN_EXISTS(TEMP_6) && ANALOG_OK(TEMP_6_PIN)
-  REPORT_NAME_ANALOG(__LINE__, TEMP_6_PIN)
+#if PIN_EXISTS(TEMP_6)
+  #if ANALOG_OK(TEMP_6_PIN)
+    REPORT_NAME_ANALOG(__LINE__, TEMP_6_PIN)
+  #endif
 #endif
-#if PIN_EXISTS(TEMP_7) && ANALOG_OK(TEMP_7_PIN)
-  REPORT_NAME_ANALOG(__LINE__, TEMP_7_PIN)
+#if PIN_EXISTS(TEMP_7)
+  #if ANALOG_OK(TEMP_7_PIN)
+    REPORT_NAME_ANALOG(__LINE__, TEMP_7_PIN)
+  #endif
 #endif
-#if PIN_EXISTS(TEMP_BED) && ANALOG_OK(TEMP_BED_PIN)
-  REPORT_NAME_ANALOG(__LINE__, TEMP_BED_PIN)
+#if PIN_EXISTS(TEMP_BED)
+  #if ANALOG_OK(TEMP_BED_PIN)
+    REPORT_NAME_ANALOG(__LINE__, TEMP_BED_PIN)
+  #endif
 #endif
-#if PIN_EXISTS(TEMP_CHAMBER) && ANALOG_OK(TEMP_CHAMBER_PIN)
-  REPORT_NAME_ANALOG(__LINE__, TEMP_CHAMBER_PIN)
+#if PIN_EXISTS(TEMP_CHAMBER)
+  #if ANALOG_OK(TEMP_CHAMBER_PIN)
+    REPORT_NAME_ANALOG(__LINE__, TEMP_CHAMBER_PIN)
+  #endif
 #endif
-#if PIN_EXISTS(TEMP_COOLER) && ANALOG_OK(TEMP_COOLER_PIN)
-  REPORT_NAME_ANALOG(__LINE__, TEMP_COOLER_PIN)
+#if PIN_EXISTS(TEMP_COOLER)
+  #if ANALOG_OK(TEMP_COOLER_PIN)
+    REPORT_NAME_ANALOG(__LINE__, TEMP_COOLER_PIN)
+  #endif
 #endif
-#if PIN_EXISTS(ADC_KEYPAD) && ANALOG_OK(ADC_KEYPAD_PIN)
-  REPORT_NAME_ANALOG(__LINE__, ADC_KEYPAD_PIN)
+#if PIN_EXISTS(ADC_KEYPAD)
+  #if ANALOG_OK(ADC_KEYPAD_PIN)
+    REPORT_NAME_ANALOG(__LINE__, ADC_KEYPAD_PIN)
+  #endif
 #endif
 
 //
 // Digital Pin Assignments
 //
 
-#if defined(__FD) && __FD >= 0
+#if _EXISTS(__FD)
   REPORT_NAME_DIGITAL(__LINE__, __FD)
 #endif
-#if defined(__FS) && __FS >= 0
+#if _EXISTS(__FS)
   REPORT_NAME_DIGITAL(__LINE__, __FS)
 #endif
-#if defined(__GD) && __GD >= 0
+#if _EXISTS(__GD)
   REPORT_NAME_DIGITAL(__LINE__, __GD)
 #endif
-#if defined(__GS) && __GS >= 0
+#if _EXISTS(__GS)
   REPORT_NAME_DIGITAL(__LINE__, __GS)
 #endif
 #if PIN_EXISTS(AVR_MISO)
@@ -137,46 +181,46 @@
 #if PIN_EXISTS(BEEPER)
   REPORT_NAME_DIGITAL(__LINE__, BEEPER_PIN)
 #endif
-#if defined(BTN_BACK) && BTN_BACK >= 0
+#if _EXISTS(BTN_BACK)
   REPORT_NAME_DIGITAL(__LINE__, BTN_BACK)
 #endif
-#if defined(BTN_CENTER) && BTN_CENTER >= 0
+#if _EXISTS(BTN_CENTER)
   REPORT_NAME_DIGITAL(__LINE__, BTN_CENTER)
 #endif
-#if defined(BTN_DOWN) && BTN_DOWN >= 0
+#if _EXISTS(BTN_DOWN)
   REPORT_NAME_DIGITAL(__LINE__, BTN_DOWN)
 #endif
-#if defined(BTN_DWN) && BTN_DWN >= 0
+#if _EXISTS(BTN_DWN)
   REPORT_NAME_DIGITAL(__LINE__, BTN_DWN)
 #endif
-#if defined(BTN_EN1) && BTN_EN1 >= 0
+#if _EXISTS(BTN_EN1)
   REPORT_NAME_DIGITAL(__LINE__, BTN_EN1)
 #endif
-#if defined(BTN_EN2) && BTN_EN2 >= 0
+#if _EXISTS(BTN_EN2)
   REPORT_NAME_DIGITAL(__LINE__, BTN_EN2)
 #endif
-#if defined(BTN_ENC_EN) && BTN_ENC_EN >= 0
+#if _EXISTS(BTN_ENC_EN)
   REPORT_NAME_DIGITAL(__LINE__, BTN_ENC_EN)
 #endif
-#if defined(BTN_ENC) && BTN_ENC >= 0
+#if _EXISTS(BTN_ENC)
   REPORT_NAME_DIGITAL(__LINE__, BTN_ENC)
 #endif
-#if defined(BTN_HOME) && BTN_HOME >= 0
+#if _EXISTS(BTN_HOME)
   REPORT_NAME_DIGITAL(__LINE__, BTN_HOME)
 #endif
-#if defined(BTN_LEFT) && BTN_LEFT >= 0
+#if _EXISTS(BTN_LEFT)
   REPORT_NAME_DIGITAL(__LINE__, BTN_LEFT)
 #endif
-#if defined(BTN_LFT) && BTN_LFT >= 0
+#if _EXISTS(BTN_LFT)
   REPORT_NAME_DIGITAL(__LINE__, BTN_LFT)
 #endif
-#if defined(BTN_RIGHT) && BTN_RIGHT >= 0
+#if _EXISTS(BTN_RIGHT)
   REPORT_NAME_DIGITAL(__LINE__, BTN_RIGHT)
 #endif
-#if defined(BTN_RT) && BTN_RT >= 0
+#if _EXISTS(BTN_RT)
   REPORT_NAME_DIGITAL(__LINE__, BTN_RT)
 #endif
-#if defined(BTN_UP) && BTN_UP >= 0
+#if _EXISTS(BTN_UP)
   REPORT_NAME_DIGITAL(__LINE__, BTN_UP)
 #endif
 #if PIN_EXISTS(JOY_X)
@@ -287,10 +331,10 @@
 #if PIN_EXISTS(CUTOFF_TEST)
   REPORT_NAME_DIGITAL(__LINE__, CUTOFF_TEST_PIN)
 #endif
-#if defined(D57) && D57 >= 0
+#if _EXISTS(D57)
   REPORT_NAME_DIGITAL(__LINE__, D57)
 #endif
-#if defined(D58) && D58 >= 0
+#if _EXISTS(D58)
   REPORT_NAME_DIGITAL(__LINE__, D58)
 #endif
 #if PIN_EXISTS(DAC_DISABLE)
@@ -305,49 +349,49 @@
 #if PIN_EXISTS(DEBUG)
   REPORT_NAME_DIGITAL(__LINE__, DEBUG_PIN)
 #endif
-#if defined(DIGIPOTS_I2C_SCL) && DIGIPOTS_I2C_SCL >= 0
+#if _EXISTS(DIGIPOTS_I2C_SCL)
   REPORT_NAME_DIGITAL(__LINE__, DIGIPOTS_I2C_SCL)
 #endif
-#if defined(DIGIPOTS_I2C_SDA_E0) && DIGIPOTS_I2C_SDA_E0 >= 0
+#if _EXISTS(DIGIPOTS_I2C_SDA_E0)
   REPORT_NAME_DIGITAL(__LINE__, DIGIPOTS_I2C_SDA_E0)
 #endif
-#if defined(DIGIPOTS_I2C_SDA_E1) && DIGIPOTS_I2C_SDA_E1 >= 0
+#if _EXISTS(DIGIPOTS_I2C_SDA_E1)
   REPORT_NAME_DIGITAL(__LINE__, DIGIPOTS_I2C_SDA_E1)
 #endif
-#if defined(DIGIPOTS_I2C_SDA_X) && DIGIPOTS_I2C_SDA_X >= 0
+#if _EXISTS(DIGIPOTS_I2C_SDA_X)
   REPORT_NAME_DIGITAL(__LINE__, DIGIPOTS_I2C_SDA_X)
 #endif
-#if defined(DIGIPOTS_I2C_SDA_Y) && DIGIPOTS_I2C_SDA_Y >= 0
+#if _EXISTS(DIGIPOTS_I2C_SDA_Y)
   REPORT_NAME_DIGITAL(__LINE__, DIGIPOTS_I2C_SDA_Y)
 #endif
-#if defined(DIGIPOTS_I2C_SDA_Z) && DIGIPOTS_I2C_SDA_Z >= 0
+#if _EXISTS(DIGIPOTS_I2C_SDA_Z)
   REPORT_NAME_DIGITAL(__LINE__, DIGIPOTS_I2C_SDA_Z)
 #endif
 #if PIN_EXISTS(DIGIPOTSS)
   REPORT_NAME_DIGITAL(__LINE__, DIGIPOTSS_PIN)
 #endif
-#if defined(DOGLCD_A0) && DOGLCD_A0 >= 0
+#if _EXISTS(DOGLCD_A0)
   REPORT_NAME_DIGITAL(__LINE__, DOGLCD_A0)
 #endif
-#if defined(DOGLCD_CS) && DOGLCD_CS >= 0
+#if _EXISTS(DOGLCD_CS)
   REPORT_NAME_DIGITAL(__LINE__, DOGLCD_CS)
 #endif
-#if defined(DOGLCD_MOSI) && DOGLCD_MOSI >= 0
+#if _EXISTS(DOGLCD_MOSI)
   REPORT_NAME_DIGITAL(__LINE__, DOGLCD_MOSI)
 #endif
-#if defined(DOGLCD_SCK) && DOGLCD_SCK >= 0
+#if _EXISTS(DOGLCD_SCK)
   REPORT_NAME_DIGITAL(__LINE__, DOGLCD_SCK)
 #endif
-#if defined(TMC_SW_MISO) && TMC_SW_MISO >= 0
+#if _EXISTS(TMC_SW_MISO)
   REPORT_NAME_DIGITAL(__LINE__, TMC_SW_MISO)
 #endif
-#if defined(TMC_SW_MOSI) && TMC_SW_MOSI >= 0
+#if _EXISTS(TMC_SW_MOSI)
   REPORT_NAME_DIGITAL(__LINE__, TMC_SW_MOSI)
 #endif
-#if defined(TMC_SW_SCK) && TMC_SW_SCK >= 0
+#if _EXISTS(TMC_SW_SCK)
   REPORT_NAME_DIGITAL(__LINE__, TMC_SW_SCK)
 #endif
-#if defined(TFTGLCD_CS) && TFTGLCD_CS >= 0
+#if _EXISTS(TFTGLCD_CS)
   REPORT_NAME_DIGITAL(__LINE__, TFTGLCD_CS)
 #endif
 #if PIN_EXISTS(E_MUX0)
@@ -557,71 +601,71 @@
 #if PIN_EXISTS(E7_STEP)
   REPORT_NAME_DIGITAL(__LINE__, E7_STEP_PIN)
 #endif
-#if defined(ENET_CRS) && ENET_CRS >= 0
+#if _EXISTS(ENET_CRS)
   REPORT_NAME_DIGITAL(__LINE__, ENET_CRS)
 #endif
-#if defined(ENET_MDIO) && ENET_MDIO >= 0
+#if _EXISTS(ENET_MDIO)
   REPORT_NAME_DIGITAL(__LINE__, ENET_MDIO)
 #endif
-#if defined(ENET_MOC) && ENET_MOC >= 0
+#if _EXISTS(ENET_MOC)
   REPORT_NAME_DIGITAL(__LINE__, ENET_MOC)
 #endif
-#if defined(ENET_RX_ER) && ENET_RX_ER >= 0
+#if _EXISTS(ENET_RX_ER)
   REPORT_NAME_DIGITAL(__LINE__, ENET_RX_ER)
 #endif
-#if defined(ENET_RXD0) && ENET_RXD0 >= 0
+#if _EXISTS(ENET_RXD0)
   REPORT_NAME_DIGITAL(__LINE__, ENET_RXD0)
 #endif
-#if defined(ENET_RXD1) && ENET_RXD1 >= 0
+#if _EXISTS(ENET_RXD1)
   REPORT_NAME_DIGITAL(__LINE__, ENET_RXD1)
 #endif
-#if defined(ENET_TX_EN) && ENET_TX_EN >= 0
+#if _EXISTS(ENET_TX_EN)
   REPORT_NAME_DIGITAL(__LINE__, ENET_TX_EN)
 #endif
-#if defined(ENET_TXD0) && ENET_TXD0 >= 0
+#if _EXISTS(ENET_TXD0)
   REPORT_NAME_DIGITAL(__LINE__, ENET_TXD0)
 #endif
-#if defined(ENET_TXD1) && ENET_TXD1 >= 0
+#if _EXISTS(ENET_TXD1)
   REPORT_NAME_DIGITAL(__LINE__, ENET_TXD1)
 #endif
 #if PIN_EXISTS(EXP_VOLTAGE_LEVEL)
   REPORT_NAME_DIGITAL(__LINE__, EXP_VOLTAGE_LEVEL_PIN)
 #endif
 
-#if defined(EXT_AUX_A0_IO) && EXT_AUX_A0_IO >= 0
+#if _EXISTS(EXT_AUX_A0_IO)
   REPORT_NAME_DIGITAL(__LINE__, EXT_AUX_A0_IO)
 #endif
-#if defined(EXT_AUX_A1_IO) && EXT_AUX_A1_IO >= 0
+#if _EXISTS(EXT_AUX_A1_IO)
   REPORT_NAME_DIGITAL(__LINE__, EXT_AUX_A1_IO)
 #endif
-#if defined(EXT_AUX_A2_IO) && EXT_AUX_A2_IO >= 0
+#if _EXISTS(EXT_AUX_A2_IO)
   REPORT_NAME_DIGITAL(__LINE__, EXT_AUX_A2_IO)
 #endif
-#if defined(EXT_AUX_A3_IO) && EXT_AUX_A3_IO >= 0
+#if _EXISTS(EXT_AUX_A3_IO)
   REPORT_NAME_DIGITAL(__LINE__, EXT_AUX_A3_IO)
 #endif
-#if defined(EXT_AUX_A4_IO) && EXT_AUX_A4_IO >= 0
+#if _EXISTS(EXT_AUX_A4_IO)
   REPORT_NAME_DIGITAL(__LINE__, EXT_AUX_A4_IO)
 #endif
-#if defined(EXT_AUX_PWM_D24) && EXT_AUX_PWM_D24 >= 0
+#if _EXISTS(EXT_AUX_PWM_D24)
   REPORT_NAME_DIGITAL(__LINE__, EXT_AUX_PWM_D24)
 #endif
-#if defined(EXT_AUX_RX1_D2) && EXT_AUX_RX1_D2 >= 0
+#if _EXISTS(EXT_AUX_RX1_D2)
   REPORT_NAME_DIGITAL(__LINE__, EXT_AUX_RX1_D2)
 #endif
-#if defined(EXT_AUX_SCL_D0) && EXT_AUX_SCL_D0 >= 0
+#if _EXISTS(EXT_AUX_SCL_D0)
   REPORT_NAME_DIGITAL(__LINE__, EXT_AUX_SCL_D0)
 #endif
-#if defined(EXT_AUX_SDA_D1) && EXT_AUX_SDA_D1 >= 0
+#if _EXISTS(EXT_AUX_SDA_D1)
   REPORT_NAME_DIGITAL(__LINE__, EXT_AUX_SDA_D1)
 #endif
-#if defined(EXT_AUX_TX1_D3) && EXT_AUX_TX1_D3 >= 0
+#if _EXISTS(EXT_AUX_TX1_D3)
   REPORT_NAME_DIGITAL(__LINE__, EXT_AUX_TX1_D3)
 #endif
-#if defined(EXTRUDER_0_AUTO_FAN) && EXTRUDER_0_AUTO_FAN >= 0
+#if _EXISTS(EXTRUDER_0_AUTO_FAN)
   REPORT_NAME_DIGITAL(__LINE__, EXTRUDER_0_AUTO_FAN)
 #endif
-#if defined(EXTRUDER_1_AUTO_FAN) && EXTRUDER_1_AUTO_FAN >= 0
+#if _EXISTS(EXTRUDER_1_AUTO_FAN)
   REPORT_NAME_DIGITAL(__LINE__, EXTRUDER_1_AUTO_FAN)
 #endif
 #if PIN_EXISTS(FAN)
@@ -735,25 +779,25 @@
 #if PIN_EXISTS(LCD_BACKLIGHT)
   REPORT_NAME_DIGITAL(__LINE__, LCD_BACKLIGHT_PIN)
 #endif
-#if defined(LCD_PINS_D4) && LCD_PINS_D4 >= 0
+#if _EXISTS(LCD_PINS_D4)
   REPORT_NAME_DIGITAL(__LINE__, LCD_PINS_D4)
 #endif
-#if defined(LCD_PINS_D5) && LCD_PINS_D5 >= 0
+#if _EXISTS(LCD_PINS_D5)
   REPORT_NAME_DIGITAL(__LINE__, LCD_PINS_D5)
 #endif
-#if defined(LCD_PINS_D6) && LCD_PINS_D6 >= 0
+#if _EXISTS(LCD_PINS_D6)
   REPORT_NAME_DIGITAL(__LINE__, LCD_PINS_D6)
 #endif
-#if defined(LCD_PINS_D7) && LCD_PINS_D7 >= 0
+#if _EXISTS(LCD_PINS_D7)
   REPORT_NAME_DIGITAL(__LINE__, LCD_PINS_D7)
 #endif
-#if defined(LCD_PINS_ENABLE) && LCD_PINS_ENABLE >= 0
+#if _EXISTS(LCD_PINS_ENABLE)
   REPORT_NAME_DIGITAL(__LINE__, LCD_PINS_ENABLE)
 #endif
-#if defined(LCD_PINS_RS) && LCD_PINS_RS >= 0
+#if _EXISTS(LCD_PINS_RS)
   REPORT_NAME_DIGITAL(__LINE__, LCD_PINS_RS)
 #endif
-#if defined(LCD_SDSS) && LCD_SDSS >= 0
+#if _EXISTS(LCD_SDSS)
   REPORT_NAME_DIGITAL(__LINE__, LCD_SDSS)
 #endif
 #if PIN_EXISTS(LED_GREEN)
@@ -799,9 +843,9 @@
   REPORT_NAME_DIGITAL(__LINE__, MAX7219_LOAD_PIN)
 #endif
 
-// #if defined(MISO) && MISO >= 0
-//   REPORT_NAME_DIGITAL(__LINE__, MISO)
-// #endif
+//#if _EXISTS(MISO)
+//  REPORT_NAME_DIGITAL(__LINE__, MISO)
+//#endif
 #if PIN_EXISTS(MISO)
   REPORT_NAME_DIGITAL(__LINE__, SD_MISO_PIN)
 #endif
@@ -817,9 +861,9 @@
 #if PIN_EXISTS(MOSFET_D)
   REPORT_NAME_DIGITAL(__LINE__, MOSFET_D_PIN)
 #endif
-// #if defined(MOSI) && MOSI >= 0
-//   REPORT_NAME_DIGITAL(__LINE__, MOSI)
-// #endif
+//#if _EXISTS(MOSI)
+//  REPORT_NAME_DIGITAL(__LINE__, MOSI)
+//#endif
 #if PIN_EXISTS(MOSI)
   REPORT_NAME_DIGITAL(__LINE__, SD_MOSI_PIN)
 #endif
@@ -862,7 +906,7 @@
 #if PIN_EXISTS(PWM_2)
   REPORT_NAME_DIGITAL(__LINE__, PWM_2_PIN)
 #endif
-#if defined(REF_CLK) && REF_CLK >= 0
+#if _EXISTS(REF_CLK)
   REPORT_NAME_DIGITAL(__LINE__, REF_CLK)
 #endif
 #if PIN_EXISTS(RAMPS_D10)
@@ -898,28 +942,28 @@
 #if PIN_EXISTS(SAFETY_TRIGGERED)
   REPORT_NAME_DIGITAL(__LINE__, SAFETY_TRIGGERED_PIN)
 #endif
-// #if defined(SCK) && SCK >= 0
-//   REPORT_NAME_DIGITAL(__LINE__, SCK)
-// #endif
+//#if _EXISTS(SCK)
+//  REPORT_NAME_DIGITAL(__LINE__, SCK)
+//#endif
 #if PIN_EXISTS(SCK)
   REPORT_NAME_DIGITAL(__LINE__, SD_SCK_PIN)
 #endif
-// #if defined(SCL) && SCL >= 0
-//   REPORT_NAME_DIGITAL(__LINE__, SCL)
-// #endif
+//#if _EXISTS(SCL)
+//  REPORT_NAME_DIGITAL(__LINE__, SCL)
+//#endif
 #if PIN_EXISTS(SD_DETECT)
   REPORT_NAME_DIGITAL(__LINE__, SD_DETECT_PIN)
 #endif
-// #if defined(SDA) && SDA >= 0
-//   REPORT_NAME_DIGITAL(__LINE__, SDA)
-// #endif
+//#if _EXISTS(SDA)
+//  REPORT_NAME_DIGITAL(__LINE__, SDA)
+//#endif
 #if PIN_EXISTS(SDPOWER)
   REPORT_NAME_DIGITAL(__LINE__, SDPOWER_PIN)
 #endif
-#if defined(SDSS) && SDSS >= 0
+#if _EXISTS(SDSS)
   REPORT_NAME_DIGITAL(__LINE__, SDSS)
 #endif
-#if defined(SERVO0) && SERVO0 >= 0
+#if _EXISTS(SERVO0)
   REPORT_NAME_DIGITAL(__LINE__, SERVO0)
 #endif
 #if PIN_EXISTS(SERVO0)
@@ -976,7 +1020,7 @@
 #if PIN_EXISTS(SOL7)
   REPORT_NAME_DIGITAL(__LINE__, SOL7_PIN)
 #endif
-#if defined(SPARE_IO) && SPARE_IO >= 0
+#if _EXISTS(SPARE_IO)
   REPORT_NAME_DIGITAL(__LINE__, SPARE_IO)
 #endif
 #if PIN_EXISTS(SPI_EEPROM1_CS)
@@ -1015,7 +1059,7 @@
 #if PIN_EXISTS(STAT_LED_BLUE)
   REPORT_NAME_DIGITAL(__LINE__, STAT_LED_BLUE_PIN)
 #endif
-#if defined(STAT_LED_RED_LED) && STAT_LED_RED_LED >= 0
+#if _EXISTS(STAT_LED_RED_LED)
   REPORT_NAME_DIGITAL(__LINE__, STAT_LED_RED_LED)
 #endif
 #if PIN_EXISTS(STAT_LED_RED)
@@ -1069,13 +1113,13 @@
 #if PIN_EXISTS(TX_ENABLE)
   REPORT_NAME_DIGITAL(__LINE__, TX_ENABLE_PIN)
 #endif
-#if defined(UI1) && UI1 >= 0
+#if _EXISTS(UI1)
   REPORT_NAME_DIGITAL(__LINE__, UI1)
 #endif
-#if defined(UI2) && UI2 >= 0
+#if _EXISTS(UI2)
   REPORT_NAME_DIGITAL(__LINE__, UI2)
 #endif
-#if defined(UNUSED_PWM) && UNUSED_PWM >= 0
+#if _EXISTS(UNUSED_PWM)
   REPORT_NAME_DIGITAL(__LINE__, UNUSED_PWM)
 #endif
 #if PIN_EXISTS(X_ATT)

Marlin/src/pins/ramps/pins_AZTEEG_X3.h

@@ -43,7 +43,7 @@
 #define SERVO0_PIN                            44  // SERVO1 port
 #define SERVO1_PIN                            55  // SERVO2 port
 
-#include "pins_RAMPS_13.h"
+#include "pins_RAMPS_13.h" // ... RAMPS
 
 //
 // LCD / Controller

Marlin/src/pins/ramps/pins_BQ_ZUM_MEGA_3D.h

@@ -115,7 +115,7 @@
 //
 // Import RAMPS 1.3 pins
 //
-#include "pins_RAMPS_13.h"
+#include "pins_RAMPS_13.h" // ... RAMPS
 
 //
 // Used by the Hephestos 2 heated bed upgrade kit

Marlin/src/pins/ramps/pins_K8200.h

@@ -30,4 +30,4 @@
 #define DEFAULT_MACHINE_NAME    "K8200"
 #define DEFAULT_SOURCE_CODE_URL "github.com/CONSULitAS/Marlin-K8200"
 
-#include "pins_3DRAG.h"
+#include "pins_3DRAG.h" // ... RAMPS

Marlin/src/pins/ramps/pins_K8400.h

@@ -50,7 +50,7 @@
 #define X_STOP_PIN                             3
 #define Y_STOP_PIN                            14
 
-#include "pins_3DRAG.h"
+#include "pins_3DRAG.h" // ... RAMPS
 
 //
 // Heaters / Fans

Marlin/src/pins/ramps/pins_LONGER3D_LKx_PRO.h

@@ -117,4 +117,4 @@
 // Other RAMPS 1.3 pins
 //
 #define IS_RAMPS_EFB                              // Override autodetection. Bed will be undefined.
-#include "pins_RAMPS_13.h"
+#include "pins_RAMPS_13.h" // ... RAMPS

Marlin/src/pins/ramps/pins_MKS_BASE_10.h

@@ -34,4 +34,4 @@
 #define BOARD_INFO_NAME "MKS BASE 1.0"
 #define MKS_BASE_VERSION 10
 
-#include "pins_MKS_BASE_common.h"
+#include "pins_MKS_BASE_common.h" // ... RAMPS

Marlin/src/pins/ramps/pins_MKS_BASE_14.h

@@ -58,7 +58,7 @@
   #define CASE_LIGHT_PIN                      11  // PB5 ** Pin24 ** PWM11
 #endif
 
-#include "pins_MKS_BASE_common.h"
+#include "pins_MKS_BASE_common.h" // ... RAMPS
 
 /*
   Available connectors on MKS BASE v1.4

Marlin/src/pins/ramps/pins_MKS_BASE_15.h

@@ -32,4 +32,4 @@
 #define BOARD_INFO_NAME "MKS BASE 1.5"
 #define MKS_BASE_VERSION 15
 
-#include "pins_MKS_BASE_common.h"
+#include "pins_MKS_BASE_common.h" // ... RAMPS

Marlin/src/pins/ramps/pins_MKS_BASE_16.h

@@ -56,4 +56,4 @@
   #define PS_ON_PIN                           -1
 #endif
 
-#include "pins_MKS_BASE_common.h"
+#include "pins_MKS_BASE_common.h" // ... RAMPS

Marlin/src/pins/ramps/pins_MKS_BASE_HEROIC.h

@@ -25,7 +25,7 @@
  * MKS BASE with Heroic HR4982 stepper drivers
  */
 
-#include "pins_MKS_BASE_15.h"
+#include "pins_MKS_BASE_15.h" // ... MKS_BASE_common ... RAMPS
 
 /**
  * Some new boards use HR4982 (Heroic) instead of the A4982 (Allegro) stepper drivers.

Marlin/src/pins/ramps/pins_RIGIDBOARD_V2.h

@@ -27,7 +27,7 @@
 
 #define BOARD_INFO_NAME "RigidBoard V2"
 
-#include "pins_RIGIDBOARD.h"
+#include "pins_RIGIDBOARD.h" // ... RAMPS
 
 //
 // Steppers

Marlin/src/pins/ramps/pins_TRIGORILLA_13.h

@@ -41,4 +41,4 @@
   #define E0_AUTO_FAN_PIN                     9
 #endif
 
-#include "pins_RAMPS_13.h"
+#include "pins_RAMPS_13.h" // ... RAMPS

Marlin/src/pins/ramps/pins_ZRIB_V20.h

@@ -26,7 +26,7 @@
  * V2 and V3 Boards only differ in USB controller, nothing affecting the pins.
  */
 
-#include "pins_MKS_GEN_13.h"
+#include "pins_MKS_GEN_13.h" // ... RAMPS
 
 #define ZRIB_V20_D6_PIN                        6  // Fan
 #define ZRIB_V20_D9_PIN                        9  // Fan2

Marlin/src/pins/ramps/pins_ZRIB_V52.h

@@ -48,7 +48,7 @@
 #define E2_ENABLE_PIN                         22
 #define HEATER_1_PIN                           7
 
-#include "pins_MKS_BASE_common.h"
+#include "pins_MKS_BASE_common.h" // ... RAMPS
 
 /*
   Available connectors on MKS BASE v1.4 (Basically same as ZRIB V5.2)

Marlin/src/pins/sanguino/pins_AZTEEG_X1.h

@@ -27,4 +27,4 @@
 
 #define BOARD_INFO_NAME "Azteeg X1"
 
-#include "pins_SANGUINOLOLU_12.h"
+#include "pins_SANGUINOLOLU_12.h" // ... SANGUINOLOLU_11

Marlin/src/pins/sanguino/pins_MELZI.h

@@ -44,4 +44,4 @@
   #endif
 #endif
 
-#include "pins_SANGUINOLOLU_12.h"
+#include "pins_SANGUINOLOLU_12.h" // ... SANGUINOLOLU_11

Marlin/src/pins/sanguino/pins_MELZI_CREALITY.h

@@ -42,7 +42,7 @@
   #define BOARD_ST7920_DELAY_3               125
 #endif
 
-#include "pins_MELZI.h"
+#include "pins_MELZI.h" // ... SANGUINOLOLU_12 ... SANGUINOLOLU_11
 
 //
 // For the stock CR-10 enable CR10_STOCKDISPLAY in Configuration.h

Marlin/src/pins/sanguino/pins_MELZI_MAKR3D.h

@@ -26,4 +26,4 @@
  */
 
 #define BOARD_INFO_NAME "Melzi (ATmega1284)"
-#include "pins_MELZI.h"
+#include "pins_MELZI.h" // ... SANGUINOLOLU_12 ... SANGUINOLOLU_11

Marlin/src/pins/sanguino/pins_MELZI_MALYAN.h

@@ -27,7 +27,7 @@
 
 #define BOARD_INFO_NAME "Melzi (Malyan)"
 
-#include "pins_MELZI.h"
+#include "pins_MELZI.h" // ... SANGUINOLOLU_12 ... SANGUINOLOLU_11
 
 #undef LCD_SDSS
 #undef LCD_PINS_RS

Marlin/src/pins/sanguino/pins_MELZI_TRONXY.h

@@ -34,7 +34,7 @@
   #define BOARD_ST7920_DELAY_3                 0
 #endif
 
-#include "pins_MELZI.h"
+#include "pins_MELZI.h" // ... SANGUINOLOLU_12 ... SANGUINOLOLU_11
 
 #undef Z_ENABLE_PIN
 #undef LCD_PINS_RS

Marlin/src/pins/sanguino/pins_MELZI_V2.h

@@ -34,4 +34,4 @@
   #define BOARD_ST7920_DELAY_3                 0
 #endif
 
-#include "pins_MELZI.h"
+#include "pins_MELZI.h" // ... SANGUINOLOLU_12 ... SANGUINOLOLU_11

Marlin/src/pins/sanguino/pins_STB_11.h

@@ -27,4 +27,4 @@
 
 #define BOARD_INFO_NAME "STB V1.1"
 
-#include "pins_SANGUINOLOLU_12.h"
+#include "pins_SANGUINOLOLU_12.h" // ... SANGUINOLOLU_11

Marlin/src/pins/stm32f1/pins_BTT_SKR_MINI_MZ_V1_0.h

@@ -23,4 +23,4 @@
 
 #define BOARD_INFO_NAME "BTT SKR Mini MZ V1.0"
 
-#include "pins_BTT_SKR_MINI_E3_V2_0.h"
+#include "pins_BTT_SKR_MINI_E3_V2_0.h" // ... BTT_SKR_MINI_E3_common

Marlin/src/pins/stm32f1/pins_MKS_ROBIN_E3D_V1_1.h

@@ -64,4 +64,4 @@
   #endif
 #endif
 
-#include "pins_MKS_ROBIN_E3_V1_1_common.h"
+#include "pins_MKS_ROBIN_E3_V1_1_common.h" // ... MKS_ROBIN_E3_common

Marlin/src/pins/stm32f1/pins_MKS_ROBIN_E3_V1_1.h

@@ -33,4 +33,4 @@
   #define BOARD_INFO_NAME "MKS Robin E3 V1.1"
 #endif
 
-#include "pins_MKS_ROBIN_E3_V1_1_common.h"
+#include "pins_MKS_ROBIN_E3_V1_1_common.h" // ... MKS_ROBIN_E3_common

Marlin/src/pins/stm32f1/pins_ZM3E2_V1_0.h

@@ -16,7 +16,7 @@
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
  *
  */
 #pragma once

Marlin/src/pins/stm32f1/pins_ZM3E4_V1_0.h

@@ -16,7 +16,7 @@
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
  *
  */
 #pragma once

Marlin/src/pins/stm32f1/pins_ZM3E4_V2_0.h

@@ -16,7 +16,7 @@
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
  *
  */
 #pragma once

buildroot/bin/mftest

@@ -155,7 +155,7 @@ if ((AUTO_BUILD)); then
   BLINE=$( grep -E "define\s+BOARD_$MB\b" Marlin/src/core/boards.h )
   BNUM=$( $SED -E 's/^.+BOARD_[^ ]+ +([0-9]+).+$/\1/' <<<"$BLINE" )
   BDESC=$( $SED -E 's/^.+\/\/ *(.+)$/\1/' <<<"$BLINE" )
-  [[ -z $BNUM ]] && { echo "Error - Can't find $MB in boards list." ; exit 1 ; }
+  [[ -z $BNUM ]] && { echo "Error - Can't find BOARD_$MB in core/boards.h." ; exit 1 ; }
   ENVS=( $( grep -EA1 "MB\(.*\b$MB\b.*\)" Marlin/src/pins/pins.h | grep -E "#include.+//.+(env|$SYS):[^ ]+" | grep -oE "(env|$SYS):[^ ]+" | $SED -E "s/(env|$SYS)://" ) )
   [[ -z $ENVS ]] && { errout "Error - Can't find target(s) for $MB ($BNUM)." ; exit 1 ; }
   ECOUNT=${#ENVS[*]}

buildroot/share/PlatformIO/scripts/common-cxxflags.py

@@ -3,13 +3,16 @@
 # Convenience script to apply customizations to CPP flags
 #
 Import("env")
-env.Append(CXXFLAGS=[
-  "-Wno-register"
+
+cxxflags = [
   #"-Wno-incompatible-pointer-types",
   #"-Wno-unused-const-variable",
   #"-Wno-maybe-uninitialized",
   #"-Wno-sign-compare"
-])
+]
+if "teensy" not in env['PIOENV']:
+	cxxflags += ["-Wno-register"]
+env.Append(CXXFLAGS=cxxflags)
 
 #
 # Add CPU frequency as a compile time constant instead of a runtime variable

buildroot/share/PlatformIO/scripts/common-dependencies.py

@@ -2,7 +2,12 @@
 # common-dependencies.py
 # Convenience script to check dependencies and add libs and sources for Marlin Enabled Features
 #
-import subprocess,os,re
+import subprocess,os,re,pioutil
+Import("env")
+
+# Detect that 'vscode init' is running
+if pioutil.is_vscode_init():
+	env.Exit(0)
 
 PIO_VERSION_MIN = (5, 0, 3)
 try:
@@ -31,8 +36,6 @@ except:
 from platformio.package.meta import PackageSpec
 from platformio.project.config import ProjectConfig
 
-Import("env")
-
 #print(env.Dump())
 
 try:

buildroot/share/PlatformIO/scripts/download_mks_assets.py

@@ -3,10 +3,15 @@
 # Added by HAS_TFT_LVGL_UI to download assets from Makerbase repo
 #
 Import("env")
-import os,requests,zipfile,tempfile,shutil
+import os,requests,zipfile,tempfile,shutil,pioutil
 
-url = "https://github.com/makerbase-mks/Mks-Robin-Nano-Marlin2.0-Firmware/archive/master.zip"
-zip_path = os.path.join(env.Dictionary("PROJECT_LIBDEPS_DIR"), "mks-assets.zip")
+# Detect that 'vscode init' is running
+if pioutil.is_vscode_init():
+	env.Exit(0)
+
+url = "https://github.com/makerbase-mks/Mks-Robin-Nano-Marlin2.0-Firmware/archive/0263cdaccf.zip"
+deps_path = env.Dictionary("PROJECT_LIBDEPS_DIR")
+zip_path = os.path.join(deps_path, "mks-assets.zip")
 assets_path = os.path.join(env.Dictionary("PROJECT_BUILD_DIR"), env.Dictionary("PIOENV"), "assets")
 
 def download_mks_assets():
@@ -14,8 +19,8 @@ def download_mks_assets():
 	r = requests.get(url, stream=True)
 	# the user may have a very clean workspace,
 	# so create the PROJECT_LIBDEPS_DIR directory if not exits
-	if os.path.exists(env.Dictionary("PROJECT_LIBDEPS_DIR")) == False:
-		os.mkdir(env.Dictionary("PROJECT_LIBDEPS_DIR"))
+	if os.path.exists(deps_path) == False:
+		os.mkdir(deps_path)
 	with open(zip_path, 'wb') as fd:
 		for chunk in r.iter_content(chunk_size=128):
 			fd.write(chunk)

buildroot/share/PlatformIO/scripts/lerdge.py

@@ -12,37 +12,36 @@ from SCons.Script import DefaultEnvironment
 board = DefaultEnvironment().BoardConfig()
 
 def encryptByte(byte):
-    byte = 0xFF & ((byte << 6) | (byte >> 2))
-    i = 0x58 + byte
-    j = 0x05 + byte + (i >> 8)
-    byte = (0xF8 & i) | (0x07 & j)
-    return byte
+	byte = 0xFF & ((byte << 6) | (byte >> 2))
+	i = 0x58 + byte
+	j = 0x05 + byte + (i >> 8)
+	byte = (0xF8 & i) | (0x07 & j)
+	return byte
 
 def encrypt_file(input, output_file, file_length):
-    input_file = bytearray(input.read())
-    for i in range(len(input_file)):
-        result = encryptByte(input_file[i])
-        input_file[i] = result
-
-    output_file.write(input_file)
-    return
+	input_file = bytearray(input.read())
+	for i in range(len(input_file)):
+		input_file[i] = encryptByte(input_file[i])
+	output_file.write(input_file)
 
 # Encrypt ${PROGNAME}.bin and save it with the name given in build.encrypt
 def encrypt(source, target, env):
-    fwname = board.get("build.encrypt")
-    print("Encrypting %s to %s" % (target[0].path, fwname))
-    firmware = open(target[0].path, "rb")
-    renamed = open(target[0].dir.path + "/" + fwname, "wb")
-    length = os.path.getsize(target[0].path)
+	fwpath = target[0].path
+	enname = board.get("build.encrypt")
+	print("Encrypting %s to %s" % (fwpath, enname))
+	fwfile = open(fwpath, "rb")
+	enfile = open(target[0].dir.path + "/" + enname, "wb")
+	length = os.path.getsize(fwpath)
 
-    encrypt_file(firmware, renamed, length)
+	encrypt_file(fwfile, enfile, length)
 
-    firmware.close()
-    renamed.close()
+	fwfile.close()
+	enfile.close()
+	os.remove(fwpath)
 
 if 'encrypt' in board.get("build").keys():
-    if board.get("build.encrypt") != "":
-        marlin.add_post_action(encrypt)
+	if board.get("build.encrypt") != "":
+		marlin.add_post_action(encrypt)
 else:
-    print("LERDGE builds require output file via board_build.encrypt = 'filename' parameter")
-    exit(1)
+	print("LERDGE builds require output file via board_build.encrypt = 'filename' parameter")
+	exit(1)

buildroot/share/PlatformIO/scripts/marlin.py

@@ -48,22 +48,24 @@ def encrypt_mks(source, target, env, new_name):
 
 	key = [0xA3, 0xBD, 0xAD, 0x0D, 0x41, 0x11, 0xBB, 0x8D, 0xDC, 0x80, 0x2D, 0xD0, 0xD2, 0xC4, 0x9B, 0x1E, 0x26, 0xEB, 0xE3, 0x33, 0x4A, 0x15, 0xE4, 0x0A, 0xB3, 0xB1, 0x3C, 0x93, 0xBB, 0xAF, 0xF7, 0x3E]
 
-	firmware = open(target[0].path, "rb")
-	renamed = open(target[0].dir.path + "/" + new_name, "wb")
-	length = os.path.getsize(target[0].path)
+	fwpath = target[0].path
+	fwfile = open(fwpath, "rb")
+	enfile = open(target[0].dir.path + "/" + new_name, "wb")
+	length = os.path.getsize(fwpath)
 	position = 0
 	try:
 		while position < length:
-			byte = firmware.read(1)
+			byte = fwfile.read(1)
 			if position >= 320 and position < 31040:
 				byte = chr(ord(byte) ^ key[position & 31])
 				if sys.version_info[0] > 2:
 					byte = bytes(byte, 'latin1')
-			renamed.write(byte)
+			enfile.write(byte)
 			position += 1
 	finally:
-		firmware.close()
-		renamed.close()
+		fwfile.close()
+		enfile.close()
+		os.remove(fwpath)
 
 def add_post_action(action):
 	env.AddPostAction(join("$BUILD_DIR", "${PROGNAME}.bin"), action);

buildroot/share/PlatformIO/scripts/pioutil.py

@@ -0,0 +1,8 @@
+#
+# buildroot/share/PlatformIO/scripts/pioutil.py
+#
+
+# Detect that 'vscode init' is running
+def is_vscode_init():
+	from SCons.Script import COMMAND_LINE_TARGETS
+	return "idedata" in COMMAND_LINE_TARGETS or "_idedata" in COMMAND_LINE_TARGETS

buildroot/share/PlatformIO/scripts/preflight-checks.py

@@ -2,9 +2,13 @@
 # preflight-checks.py
 # Check for common issues prior to compiling
 #
-import os,re,sys
+import os,re,sys,pioutil
 Import("env")
 
+# Detect that 'vscode init' is running
+if pioutil.is_vscode_init():
+	env.Exit(0)
+
 def get_envs_for_board(board):
 	with open(os.path.join("Marlin", "src", "pins", "pins.h"), "r") as file:
 
@@ -94,7 +98,4 @@ def sanity_check_target():
 		err = "ERROR: Old files fell into your Marlin folder. Remove %s and try again" % ", ".join(mixedin)
 		raise SystemExit(err)
 
-# Detect that 'vscode init' is running
-from SCons.Script import COMMAND_LINE_TARGETS
-if "idedata" not in COMMAND_LINE_TARGETS:
-	sanity_check_target()
+sanity_check_target()

ini/stm32f4.ini

@@ -263,13 +263,13 @@ platform            = ${common_stm32.platform}
 extends             = stm32_variant
 board               = marlin_STM32F407ZGT6
 board_build.variant = MARLIN_LERDGE
-board_build.encrypt = firmware.bin
 board_build.offset  = 0x10000
 build_flags         = ${stm32_variant.build_flags}
                       -DSTM32F4 -DSTM32F4xx -DTARGET_STM32F4
                       -DDISABLE_GENERIC_SERIALUSB -DARDUINO_ARCH_STM32 -DLERDGE_TFT35
 build_unflags       = ${stm32_variant.build_unflags} -DUSBCON -DUSBD_USE_CDC -DUSBD_VID=0x0483
-extra_scripts       = ${stm32_variant.extra_scripts}
+extra_scripts       = ${common_stm32.extra_scripts}
+                      pre:buildroot/share/PlatformIO/scripts/generic_create_variant.py
                       buildroot/share/PlatformIO/scripts/lerdge.py
 
 #