EXP3D Imprimante Multifonction (#16079)

Marlin/src/module/scara.cpp

@@ -95,7 +95,7 @@ void forward_kinematics_SCARA(const float &a, const float &b) {
 void inverse_kinematics(const xyz_pos_t &raw) {
 
   #if ENABLED(MORGAN_SCARA)
-  
+
     /**
      * Morgan SCARA Inverse Kinematics. Results in 'delta'.
      *

Marlin/src/pins/pins.h

@@ -460,7 +460,7 @@
 #elif MB(GTM32_MINI_A30)
   #include "stm32/pins_GTM32_MINI_A30.h"        // STM32F1                                env:STM32F103RE
 #elif MB(GTM32_MINI)
-  #include "stm32/pins_GTM32_MINI.h"            // STM32F1                                env:STM32F103RE 
+  #include "stm32/pins_GTM32_MINI.h"            // STM32F1                                env:STM32F103RE
 #elif MB(GTM32_REV_B)
   #include "stm32/pins_GTM32_REV_B.h"           // STM32F1                                env:STM32F103RE
 #elif MB(MORPHEUS)

config/examples/Geeetech/E180/Configuration.h

@@ -476,7 +476,7 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   //FIND YOUR OWN: "M303 C8 S200 U" HOTEND PID
-  
+
   #define  DEFAULT_Kp 45.80
   #define  DEFAULT_Ki 3.61
   #define  DEFAULT_Kd 145.39
@@ -515,7 +515,6 @@
 #if ENABLED(PIDTEMPBED)
   //#define MIN_BED_POWER 0
   //#define PID_BED_DEBUG // Sends debug data to the serial port.
-  
 
   // FIND YOUR OWN: "M303 E-1 C8 S60"
 #endif // PIDTEMPBED
@@ -1084,7 +1083,7 @@
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_PIN      66
-  #define FIL_RUNOUT_INVERTING true  // set to true to invert the logic of the sensors. - some of the geeetech filament sensors are false 
+  #define FIL_RUNOUT_INVERTING true  // set to true to invert the logic of the sensors. - some of the geeetech filament sensors are false
   #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 

config/examples/Geeetech/E180/Configuration_adv.h

@@ -1722,7 +1722,7 @@
  * Requires NOZZLE_PARK_FEATURE.
  * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
  */
-//#define ADVANCED_PAUSE_FEATURE 
+//#define ADVANCED_PAUSE_FEATURE
 #if ENABLED(ADVANCED_PAUSE_FEATURE)
   #define PAUSE_PARK_RETRACT_FEEDRATE         10  // (mm/s) Initial retract feedrate.
   #define PAUSE_PARK_RETRACT_LENGTH            2  // (mm) Initial retract.