Multi-line comments cleanup (#19535)

4 years ago · 04a712dacc
131 changed files with 11 additions and 176 deletions
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@ -34,7 +34,6 @@
 * - Extra features
 *
 * Advanced settings can be found in Configuration_adv.h
- *
 */
 #define CONFIGURATION_H_VERSION 020007

@ -855,7 +854,6 @@
 *    - For simple switches connect...
 *      - normally-closed switches to GND and D32.
 *      - normally-open switches to 5V and D32.
- *
 */
 //#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default

@ -1567,7 +1565,6 @@
 *
 *   Caveats: The ending Z should be the same as starting Z.
 * Attention: EXPERIMENTAL. G-code arguments may change.
- *
 */
 //#define NOZZLE_CLEAN_FEATURE

@ -1720,7 +1717,6 @@
 *
 * SD Card support is disabled by default. If your controller has an SD slot,
 * you must uncomment the following option or it won't work.
- *
 */
 //#define SDSUPPORT

@ -2343,7 +2339,6 @@
 * *** CAUTION ***
 *
 * LED Type. Enable only one of the following two options.
- *
 */
 //#define RGB_LED
 //#define RGBW_LED
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@ -29,7 +29,6 @@
 * Some of these settings can damage your printer if improperly set!
 *
 * Basic settings can be found in Configuration.h
- *
 */
 #define CONFIGURATION_ADV_H_VERSION 020007

@ -738,7 +737,6 @@
   *               | 4   3 | 1   4 | 2   1 | 3   2 |
   *               |       |       |       |       |
   *               | 1   2 | 2   3 | 3   4 | 4   1 |
-   *
   */
  #ifndef Z_STEPPER_ALIGN_XY
    //#define Z_STEPPERS_ORIENTATION 0
@ -1954,7 +1952,6 @@
 * Be sure to turn off auto-retract during filament change.
 *
 * Note that M207 / M208 / M209 settings are saved to EEPROM.
- *
 */
 //#define FWRETRACT
 #if ENABLED(FWRETRACT)
--- a/Marlin/src/HAL/AVR/HAL.h
+++ b/Marlin/src/HAL/AVR/HAL.h
@ -15,6 +15,7 @@
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <https://www.gnu.org/licenses/>.
+ *
 */
 #pragma once

--- a/Marlin/src/HAL/AVR/Servo.cpp
+++ b/Marlin/src/HAL/AVR/Servo.cpp
@ -48,7 +48,6 @@
 * readMicroseconds()    - Get the last-written servo pulse width in microseconds.
 * attached()            - Return true if a servo is attached.
 * detach()              - Stop an attached servo from pulsing its i/o pin.
- *
 */

 #ifdef __AVR__
--- a/Marlin/src/HAL/AVR/timers.h
+++ b/Marlin/src/HAL/AVR/timers.h
@ -15,6 +15,7 @@
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <https://www.gnu.org/licenses/>.
+ *
 */
 #pragma once

--- a/Marlin/src/HAL/DUE/HAL_SPI.cpp
+++ b/Marlin/src/HAL/DUE/HAL_SPI.cpp
@ -759,7 +759,6 @@
     *
     *  All of the above can be avoided by defining FORCE_SOFT_SPI to force the
     *  display to use software SPI.
-     *
     */

    void spiInit(uint8_t spiRate=6) {  // Default to slowest rate if not specified)
--- a/Marlin/src/HAL/DUE/dogm/u8g_com_HAL_DUE_shared_hw_spi.cpp
+++ b/Marlin/src/HAL/DUE/dogm/u8g_com_HAL_DUE_shared_hw_spi.cpp
@ -52,7 +52,6 @@
 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF
 * ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
 */

 #ifdef __SAM3X8E__
--- a/Marlin/src/HAL/DUE/eeprom_flash.cpp
+++ b/Marlin/src/HAL/DUE/eeprom_flash.cpp
@ -53,7 +53,6 @@
 * per page. We can't emulate EE endurance with FLASH for all
 * bytes, but we can emulate endurance for a given percent of
 * bytes.
- *
 */

 //#define EE_EMU_DEBUG
--- a/Marlin/src/HAL/DUE/pinsDebug.h
+++ b/Marlin/src/HAL/DUE/pinsDebug.h
@ -179,5 +179,4 @@ void pwm_details(int32_t pin) {
 * ----------------+--------
 *  ID             |  PB11
 *  VBOF           |  PB10
- *
 */
--- a/Marlin/src/HAL/ESP32/HAL.h
+++ b/Marlin/src/HAL/ESP32/HAL.h
@ -15,6 +15,7 @@
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <https://www.gnu.org/licenses/>.
+ *
 */
 #pragma once

--- a/Marlin/src/HAL/ESP32/ota.h
+++ b/Marlin/src/HAL/ESP32/ota.h
@ -15,6 +15,7 @@
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <https://www.gnu.org/licenses/>.
+ *
 */
 #pragma once

--- a/Marlin/src/HAL/LINUX/include/serial.h
+++ b/Marlin/src/HAL/LINUX/include/serial.h
@ -33,7 +33,6 @@
 * Generic RingBuffer
 * T type of the buffer array
 * S size of the buffer (must be power of 2)
- *
 */
 template <typename T, uint32_t S> class RingBuffer {
 public:
--- a/Marlin/src/HAL/LINUX/servo_private.h
+++ b/Marlin/src/HAL/LINUX/servo_private.h
@ -45,7 +45,6 @@
 *           Version 2 Copyright (c) 2009 Michael Margolis.  All right reserved.
 *
 * The only modification was to update/delete macros to match the LPC176x.
- *
 */

 #include <stdint.h>
--- a/Marlin/src/HAL/LPC1768/Servo.h
+++ b/Marlin/src/HAL/LPC1768/Servo.h
@ -46,7 +46,6 @@
 *           Version 2 Copyright (c) 2009 Michael Margolis.  All right reserved.
 *
 * The only modification was to update/delete macros to match the LPC176x.
- *
 */

 #include <Servo.h>
--- a/Marlin/src/HAL/LPC1768/timers.h
+++ b/Marlin/src/HAL/LPC1768/timers.h
@ -21,7 +21,6 @@
 #pragma once

 /**
- *
 * HAL For LPC1768
 */

--- a/Marlin/src/HAL/SAMD51/QSPIFlash.h
+++ b/Marlin/src/HAL/SAMD51/QSPIFlash.h
@ -24,7 +24,6 @@
 * THE SOFTWARE.
 *
 * Derived from Adafruit_SPIFlash class with no SdFat references
- *
 */

 #pragma once
--- a/Marlin/src/HAL/SAMD51/pinsDebug.h
+++ b/Marlin/src/HAL/SAMD51/pinsDebug.h
@ -150,5 +150,4 @@ void pwm_details(int32_t pin) {
 *  93             |  PA10  | QSPI: IO2
 *  94             |  PA11  | QSPI: IO3
 *  95             |  PB31  | SD: DETECT
- *
 */
--- a/Marlin/src/HAL/STM32F1/onboard_sd.cpp
+++ b/Marlin/src/HAL/STM32F1/onboard_sd.cpp
@ -9,7 +9,6 @@
 * No restriction on use. You can use, modify and redistribute it for
 * personal, non-profit or commercial products UNDER YOUR RESPONSIBILITY.
 * Redistributions of source code must retain the above copyright notice.
- *
 */

 #include "../../inc/MarlinConfig.h"
--- a/Marlin/src/HAL/STM32_F4_F7/STM32F7/TMC2660.cpp
+++ b/Marlin/src/HAL/STM32_F4_F7/STM32F7/TMC2660.cpp
@ -22,7 +22,6 @@
 * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
 * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
 * THE SOFTWARE.
- *
 */

 #if defined(STM32GENERIC) && defined(STM32F7)
@ -662,7 +661,6 @@ boolean TMC26XStepper::isEnabled() { return !!(chopper_config_register & T_OFF_P
 /**
 * reads a value from the TMC26X status register. The value is not obtained directly but can then
 * be read by the various status routines.
- *
 */
 void TMC26XStepper::readStatus(char read_value) {
  uint32_t old_driver_configuration_register_value = driver_configuration_register_value;
--- a/Marlin/src/HAL/STM32_F4_F7/STM32F7/TMC2660.h
+++ b/Marlin/src/HAL/STM32_F4_F7/STM32F7/TMC2660.h
@ -22,7 +22,6 @@
 * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
 * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
 * THE SOFTWARE.
- *
 */
 #pragma once

--- a/Marlin/src/HAL/TEENSY35_36/timers.h
+++ b/Marlin/src/HAL/TEENSY35_36/timers.h
@ -16,6 +16,7 @@
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <https://www.gnu.org/licenses/>.
+ *
 */
 #pragma once

--- a/Marlin/src/HAL/TEENSY40_41/timers.h
+++ b/Marlin/src/HAL/TEENSY40_41/timers.h
@ -16,6 +16,7 @@
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <https://www.gnu.org/licenses/>.
+ *
 */
 #pragma once

--- a/Marlin/src/HAL/shared/servo.cpp
+++ b/Marlin/src/HAL/shared/servo.cpp
@ -48,7 +48,6 @@
 * readMicroseconds()    - Get the last-written servo pulse width in microseconds.
 * attached()            - Return true if a servo is attached.
 * detach()              - Stop an attached servo from pulsing its i/o pin.
- *
 */

 #include "../../inc/MarlinConfig.h"
--- a/Marlin/src/HAL/shared/servo.h
+++ b/Marlin/src/HAL/shared/servo.h
@ -41,7 +41,6 @@
 */

 /**
- *
 * A servo is activated by creating an instance of the Servo class passing the desired pin to the attach() method.
 * The servos are pulsed in the background using the value most recently written using the write() method
 *
--- a/Marlin/src/core/language.h
+++ b/Marlin/src/core/language.h
@ -348,7 +348,6 @@
 * However, internal to Marlin E0/T0 is the first tool, and
 * most board silkscreens say "E0." Zero-based labels will
 * make these indexes consistent but this defies expectation.
- *
 */
 #if ENABLED(NUMBER_TOOLS_FROM_0)
  #define LCD_FIRST_TOOL 0
--- a/Marlin/src/feature/bedlevel/ubl/ubl_motion.cpp
+++ b/Marlin/src/feature/bedlevel/ubl/ubl_motion.cpp
@ -236,9 +236,7 @@
    }

    /**
-     *
     * Generic case of a line crossing both X and Y Mesh lines.
-     *
     */

    xy_int8_t cnt = (istart - iend).ABS();
--- a/Marlin/src/feature/encoder_i2c.cpp
+++ b/Marlin/src/feature/encoder_i2c.cpp
@ -816,7 +816,6 @@ int8_t I2CPositionEncodersMgr::parse() {
 *    Y       Report on Y axis encoder, if present.
 *    Z       Report on Z axis encoder, if present.
 *    E       Report on E axis encoder, if present.
- *
 */
 void I2CPositionEncodersMgr::M860() {
  if (parse()) return;
@ -846,7 +845,6 @@ void I2CPositionEncodersMgr::M860() {
 *    Y       Report on Y axis encoder, if present.
 *    Z       Report on Z axis encoder, if present.
 *    E       Report on E axis encoder, if present.
- *
 */
 void I2CPositionEncodersMgr::M861() {
  if (parse()) return;
@ -875,7 +873,6 @@ void I2CPositionEncodersMgr::M861() {
 *    Y       Report on Y axis encoder, if present.
 *    Z       Report on Z axis encoder, if present.
 *    E       Report on E axis encoder, if present.
- *
 */
 void I2CPositionEncodersMgr::M862() {
  if (parse()) return;
@ -905,7 +902,6 @@ void I2CPositionEncodersMgr::M862() {
 *    Y       Report on Y axis encoder, if present.
 *    Z       Report on Z axis encoder, if present.
 *    E       Report on E axis encoder, if present.
- *
 */
 void I2CPositionEncodersMgr::M863() {
  if (parse()) return;
--- a/Marlin/src/feature/mmu2/mmu2.cpp
+++ b/Marlin/src/feature/mmu2/mmu2.cpp
@ -710,13 +710,11 @@ void MMU2::tool_change(const uint8_t index) {
 }

 /**
- *
 * Handle special T?/Tx/Tc commands
 *
 * T? Gcode to extrude shouldn't have to follow, load to extruder wheels is done automatically
 * Tx Same as T?, except nozzle doesn't have to be preheated. Tc must be placed after extruder nozzle is preheated to finish filament load.
 * Tc Load to nozzle after filament was prepared by Tx and extruder nozzle is already heated.
- *
 */
 void MMU2::tool_change(const char* special) {
  if (!enabled) return;
@ -922,9 +920,7 @@ void MMU2::filament_runout() {
  }

  /**
-   *
   * Switch material and load to nozzle
-   *
   */
  bool MMU2::load_filament_to_nozzle(const uint8_t index) {

--- a/Marlin/src/feature/twibus.h
+++ b/Marlin/src/feature/twibus.h
@ -48,7 +48,6 @@ typedef void (*twiRequestFunc_t)();
 *  For more information see
 *    - https://marlinfw.org/docs/gcode/M260.html
 *    - https://marlinfw.org/docs/gcode/M261.html
- *
 */
 class TWIBus {
  private:
--- a/Marlin/src/gcode/bedlevel/abl/G29.cpp
+++ b/Marlin/src/gcode/bedlevel/abl/G29.cpp
@ -160,7 +160,6 @@
 *  E  By default G29 will engage the Z probe, test the bed, then disengage.
 *     Include "E" to engage/disengage the Z probe for each sample.
 *     There's no extra effect if you have a fixed Z probe.
- *
 */
 G29_TYPE GcodeSuite::G29() {

--- a/Marlin/src/gcode/bedlevel/mbl/G29.cpp
+++ b/Marlin/src/gcode/bedlevel/mbl/G29.cpp
@ -57,7 +57,6 @@ inline void echo_not_entered(const char c) { SERIAL_CHAR(c); SERIAL_ECHOLNPGM("
 *  S3 In Jn Zn.nn  Manually modify a single point
 *  S4 Zn.nn        Set z offset. Positive away from bed, negative closer to bed.
 *  S5              Reset and disable mesh
- *
 */
 void GcodeSuite::G29() {

--- a/Marlin/src/gcode/calibrate/G28.cpp
+++ b/Marlin/src/gcode/calibrate/G28.cpp
@ -192,7 +192,6 @@
 *  X   Home to the X endstop
 *  Y   Home to the Y endstop
 *  Z   Home to the Z endstop
- *
 */
 void GcodeSuite::G28() {
  DEBUG_SECTION(log_G28, "G28", DEBUGGING(LEVELING));
--- a/Marlin/src/gcode/control/M999.cpp
+++ b/Marlin/src/gcode/control/M999.cpp
@ -34,7 +34,6 @@
 *
 * Sending "M999 S1" will resume printing without flushing the
 * existing command buffer.
- *
 */
 void GcodeSuite::M999() {
  marlin_state = MF_RUNNING;
--- a/Marlin/src/gcode/feature/L6470/M906.cpp
+++ b/Marlin/src/gcode/feature/L6470/M906.cpp
@ -33,7 +33,6 @@
 #include "../../../core/debug_out.h"

 /**
- *
 * M906: report or set KVAL_HOLD which sets the maximum effective voltage provided by the
 *       PWMs to the steppers
 *
@ -56,7 +55,6 @@
 *
 * L6470 is used in the STEP-CLOCK mode.  KVAL_HOLD is the only KVAL_xxx
 * that affects the effective voltage seen by the stepper.
- *
 */

 /**
--- a/Marlin/src/gcode/feature/L6470/M916-918.cpp
+++ b/Marlin/src/gcode/feature/L6470/M916-918.cpp
@ -37,7 +37,6 @@
 #include "../../../core/debug_out.h"

 /**
- *
 * M916: increase KVAL_HOLD until get thermal warning
 *       NOTE - on L6474 it is TVAL that is used
 *
@ -62,7 +61,6 @@
 *
 * D - time (in seconds) to run each setting of KVAL_HOLD/TVAL
 *     optional - defaults to zero (runs each setting once)
- *
 */

 /**
@ -187,7 +185,6 @@ void GcodeSuite::M916() {
 }

 /**
- *
 * M917: Find minimum current thresholds
 *
 *   Decrease OCD current until overcurrent error
@ -214,7 +211,6 @@ void GcodeSuite::M916() {
 *
 * K - value for KVAL_HOLD (0 - 255) (ignored for L6474)
 *     optional - will report current value from driver if not specified
- *
 */
 void GcodeSuite::M917() {

@ -522,7 +518,6 @@ void GcodeSuite::M917() {
 }

 /**
- *
 * M918: increase speed until error or max feedrate achieved (as shown in configuration.h))
 *
 * J - select which driver(s) to monitor on multi-driver axis
@ -543,7 +538,6 @@ void GcodeSuite::M917() {
 *
 * M - value for microsteps (1 - 128) (optional)
 *     optional - will report current value from driver if not specified
- *
 */
 void GcodeSuite::M918() {

--- a/Marlin/src/gcode/feature/i2c/M260_M261.cpp
+++ b/Marlin/src/gcode/feature/i2c/M260_M261.cpp
@ -42,7 +42,6 @@
 *
 *  M260 S1 ; Send the buffered data and reset the buffer
 *  M260 R1 ; Reset the buffer without sending data
- *
 */
 void GcodeSuite::M260() {
  // Set the target address
--- a/Marlin/src/gcode/feature/pause/M603.cpp
+++ b/Marlin/src/gcode/feature/pause/M603.cpp
@ -39,7 +39,6 @@
 *  T[toolhead] - Select extruder to configure, active extruder if not specified
 *  U[distance] - Retract distance for removal, for the specified extruder
 *  L[distance] - Extrude distance for insertion, for the specified extruder
- *
 */
 void GcodeSuite::M603() {

--- a/Marlin/src/gcode/gcode.h
+++ b/Marlin/src/gcode/gcode.h
@ -289,7 +289,6 @@
 * "T" Codes
 *
 * T0-T3 - Select an extruder (tool) by index: "T<n> F<units/min>"
- *
 */

 #include "../inc/MarlinConfig.h"
--- a/Marlin/src/gcode/sd/M32.cpp
+++ b/Marlin/src/gcode/sd/M32.cpp
@ -38,7 +38,6 @@
 *    M32 !PATH/TO/FILE.GCO#      ; Start FILE.GCO
 *    M32 P !PATH/TO/FILE.GCO#    ; Start FILE.GCO as a procedure
 *    M32 S60 !PATH/TO/FILE.GCO#  ; Start FILE.GCO at byte 60
- *
 */
 void GcodeSuite::M32() {
  if (IS_SD_PRINTING()) planner.synchronize();
--- a/Marlin/src/inc/Conditionals_LCD.h
+++ b/Marlin/src/inc/Conditionals_LCD.h
@ -512,7 +512,6 @@
 *  HOTENDS      - Number of hotends, whether connected or separate
 *  E_STEPPERS   - Number of actual E stepper motors
 *  E_MANUAL     - Number of E steppers for LCD move options
- *
 */

 #if EXTRUDERS == 0
--- a/Marlin/src/lcd/dogm/status_screen_lite_ST7920.cpp
+++ b/Marlin/src/lcd/dogm/status_screen_lite_ST7920.cpp
@ -11,7 +11,6 @@
 * any later version.  The code is distributed WITHOUT ANY WARRANTY;
 * without even the implied warranty of MERCHANTABILITY or FITNESS
 * FOR A PARTICULAR PURPOSE.  See the GNU GPL for more details.
- *
 */

 /**
--- a/Marlin/src/lcd/dogm/status_screen_lite_ST7920.h
+++ b/Marlin/src/lcd/dogm/status_screen_lite_ST7920.h
@ -11,7 +11,6 @@
 * any later version.  The code is distributed WITHOUT ANY WARRANTY;
 * without even the implied warranty of MERCHANTABILITY or FITNESS
 * FOR A PARTICULAR PURPOSE.  See the GNU GPL for more details.
- *
 */
 #pragma once

--- a/Marlin/src/lcd/dogm/u8g_dev_tft_320x240_upscale_from_128x64.cpp
+++ b/Marlin/src/lcd/dogm/u8g_dev_tft_320x240_upscale_from_128x64.cpp
@ -51,7 +51,6 @@
 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF
 * ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
 */

 #include "../../inc/MarlinConfig.h"
--- a/Marlin/src/lcd/dwin/e3v2/dwin.cpp
+++ b/Marlin/src/lcd/dwin/e3v2/dwin.cpp
@ -1632,7 +1632,6 @@ void update_variable() {
 * TODO: New code can follow the pattern of menu_media.cpp
 * and rely on Marlin caching for performance. No need to
 * cache files here.
- *
 */

 #ifndef strcasecmp_P
--- a/Marlin/src/lcd/extui/lib/ftdi_eve_touch_ui/archim2-flash/flash_storage.cpp
+++ b/Marlin/src/lcd/extui/lib/ftdi_eve_touch_ui/archim2-flash/flash_storage.cpp
@ -42,7 +42,6 @@ constexpr uint32_t flash_eeprom_version = 1;
 * 0       16       DATA STORAGE AREA
 * 16      1        VERSIONING DATA
 * 17      inf      MEDIA STORAGE AREA
- *
 */

 #define DATA_STORAGE_SIZE_64K
--- a/Marlin/src/lcd/extui/lib/ftdi_eve_touch_ui/ftdi_eve_lib/basic/resolutions.h
+++ b/Marlin/src/lcd/extui/lib/ftdi_eve_touch_ui/ftdi_eve_lib/basic/resolutions.h
@ -32,7 +32,6 @@
 *     Selecting an LCD Display
 *     Version 2.1
 *     Issue Date: 2017-11-14
- *
 */
 #define COMPUTE_REGS_FROM_DATASHEET \
    constexpr uint16_t Hoffset              = thfp + thb - 1; \
--- a/Marlin/src/lcd/extui/lib/ftdi_eve_touch_ui/ftdi_eve_lib/extended/event_loop.cpp
+++ b/Marlin/src/lcd/extui/lib/ftdi_eve_touch_ui/ftdi_eve_lib/extended/event_loop.cpp
@ -109,7 +109,6 @@ namespace FTDI {
   *  - Handles auto-repetition by sending onTouchHeld to the active screen periodically.
   *  - Plays touch feedback "click" sounds when appropriate.
   *  - Performs debouncing to supress spurious touch events.
-   *
   */
  void EventLoop::process_events() {
    // If the LCD is processing commands, don't check
--- a/Marlin/src/lcd/extui/lib/ftdi_eve_touch_ui/ftdi_eve_lib/extras/poly_ui.h
+++ b/Marlin/src/lcd/extui/lib/ftdi_eve_touch_ui/ftdi_eve_lib/extras/poly_ui.h
@ -49,7 +49,6 @@
 *       ...
 *     }
 *   }
- *
 */

 class PolyReader {
--- a/Marlin/src/lcd/extui/ui_api.h
+++ b/Marlin/src/lcd/extui/ui_api.h
@ -375,7 +375,6 @@ namespace ExtUI {
 *   constexpr float increment = 10;
 *
 *   UI_INCREMENT(TargetTemp_celsius, E0)
- *
 */
 #define UI_INCREMENT_BY(method, inc, ...) ExtUI::set ## method(ExtUI::get ## method (__VA_ARGS__) + inc, ##__VA_ARGS__)
 #define UI_DECREMENT_BY(method, inc, ...) ExtUI::set ## method(ExtUI::get ## method (__VA_ARGS__) - inc, ##__VA_ARGS__)
--- a/Marlin/src/lcd/language/language_an.h
+++ b/Marlin/src/lcd/language/language_an.h
@ -26,7 +26,6 @@
 *
 * LCD Menu Messages
 * See also https://marlinfw.org/docs/development/lcd_language.html
- *
 */

 #define DISPLAY_CHARSET_ISO10646_1
--- a/Marlin/src/lcd/language/language_bg.h
+++ b/Marlin/src/lcd/language/language_bg.h
@ -26,7 +26,6 @@
 *
 * LCD Menu Messages
 * See also https://marlinfw.org/docs/development/lcd_language.html
- *
 */

 #define DISPLAY_CHARSET_ISO10646_5
--- a/Marlin/src/lcd/language/language_ca.h
+++ b/Marlin/src/lcd/language/language_ca.h
@ -26,7 +26,6 @@
 *
 * LCD Menu Messages
 * See also https://marlinfw.org/docs/development/lcd_language.html
- *
 */
 namespace Language_ca {
  using namespace Language_en; // Inherit undefined strings from English
--- a/Marlin/src/lcd/language/language_cz.h
+++ b/Marlin/src/lcd/language/language_cz.h
@ -31,7 +31,6 @@
 * Translated by Petr Zahradnik, Computer Laboratory
 * Blog and video blog Zahradnik se bavi
 * https://www.zahradniksebavi.cz
- *
 */

 #define DISPLAY_CHARSET_ISO10646_CZ
--- a/Marlin/src/lcd/language/language_da.h
+++ b/Marlin/src/lcd/language/language_da.h
@ -26,7 +26,6 @@
 *
 * LCD Menu Messages
 * See also https://marlinfw.org/docs/development/lcd_language.html
- *
 */

 #define DISPLAY_CHARSET_ISO10646_1
--- a/Marlin/src/lcd/language/language_de.h
+++ b/Marlin/src/lcd/language/language_de.h
@ -26,7 +26,6 @@
 *
 * LCD Menu Messages
 * See also https://marlinfw.org/docs/development/lcd_language.html
- *
 */

 namespace Language_de {
--- a/Marlin/src/lcd/language/language_el.h
+++ b/Marlin/src/lcd/language/language_el.h
@ -26,7 +26,6 @@
 *
 * LCD Menu Messages
 * See also https://marlinfw.org/docs/development/lcd_language.html
- *
 */

 #define DISPLAY_CHARSET_ISO10646_GREEK
--- a/Marlin/src/lcd/language/language_el_gr.h
+++ b/Marlin/src/lcd/language/language_el_gr.h
@ -26,7 +26,6 @@
 *
 * LCD Menu Messages
 * See also https://marlinfw.org/docs/development/lcd_language.html
- *
 */

 #define DISPLAY_CHARSET_ISO10646_GREEK
--- a/Marlin/src/lcd/language/language_en.h
+++ b/Marlin/src/lcd/language/language_en.h
@ -26,7 +26,6 @@
 *
 * LCD Menu Messages
 * See also https://marlinfw.org/docs/development/lcd_language.html
- *
 */

 #define en 1234
--- a/Marlin/src/lcd/language/language_es.h
+++ b/Marlin/src/lcd/language/language_es.h
@ -26,7 +26,6 @@
 *
 * LCD Menu Messages
 * See also https://marlinfw.org/docs/development/lcd_language.html
- *
 */

 namespace Language_es {
--- a/Marlin/src/lcd/language/language_eu.h
+++ b/Marlin/src/lcd/language/language_eu.h
@ -26,7 +26,6 @@
 *
 * LCD Menu Messages
 * See also https://marlinfw.org/docs/development/lcd_language.html
- *
 */

 #define DISPLAY_CHARSET_ISO10646_1
--- a/Marlin/src/lcd/language/language_fi.h
+++ b/Marlin/src/lcd/language/language_fi.h
@ -26,7 +26,6 @@
 *
 * LCD Menu Messages
 * See also https://marlinfw.org/docs/development/lcd_language.html
- *
 */

 #define DISPLAY_CHARSET_ISO10646_1
--- a/Marlin/src/lcd/language/language_fr.h
+++ b/Marlin/src/lcd/language/language_fr.h
@ -26,7 +26,6 @@
 *
 * LCD Menu Messages
 * See also https://marlinfw.org/docs/development/lcd_language.html
- *
 */

 #define DISPLAY_CHARSET_ISO10646_1
--- a/Marlin/src/lcd/language/language_gl.h
+++ b/Marlin/src/lcd/language/language_gl.h
@ -26,7 +26,6 @@
 *
 * LCD Menu Messages
 * See also https://marlinfw.org/docs/development/lcd_language.html
- *
 */

 #define DISPLAY_CHARSET_ISO10646_1
--- a/Marlin/src/lcd/language/language_hr.h
+++ b/Marlin/src/lcd/language/language_hr.h
@ -26,7 +26,6 @@
 *
 * LCD Menu Messages
 * See also https://marlinfw.org/docs/development/lcd_language.html
- *
 */

 #define DISPLAY_CHARSET_ISO10646_1 // use the better font on full graphic displays.
--- a/Marlin/src/lcd/language/language_hu.h
+++ b/Marlin/src/lcd/language/language_hu.h
@ -29,7 +29,6 @@
 * A Magyar fordítást készítette: AntoszHUN
 *
 *
- *
 */

 namespace Language_hu {
--- a/Marlin/src/lcd/language/language_it.h
+++ b/Marlin/src/lcd/language/language_it.h
@ -26,7 +26,6 @@
 *
 * LCD Menu Messages
 * See also https://marlinfw.org/docs/development/lcd_language.html
- *
 */

 #define DISPLAY_CHARSET_ISO10646_1
--- a/Marlin/src/lcd/language/language_jp_kana.h
+++ b/Marlin/src/lcd/language/language_jp_kana.h
@ -27,7 +27,6 @@
 *
 * LCD Menu Messages
 * See also https://marlinfw.org/docs/development/lcd_language.html
- *
 */

 //#define DISPLAY_CHARSET_ISO10646_KANA
--- a/Marlin/src/lcd/language/language_ko_KR.h
+++ b/Marlin/src/lcd/language/language_ko_KR.h
@ -26,7 +26,6 @@
 *
 * LCD Menu Messages
 * See also https://marlinfw.org/docs/development/lcd_language.html
- *
 */
 namespace Language_ko_KR {
  using namespace Language_en; // Inherit undefined strings from English
--- a/Marlin/src/lcd/language/language_nl.h
+++ b/Marlin/src/lcd/language/language_nl.h
@ -26,7 +26,6 @@
 *
 * LCD Menu Messages
 * See also https://marlinfw.org/docs/development/lcd_language.html
- *
 */

 #define DISPLAY_CHARSET_ISO10646_1
--- a/Marlin/src/lcd/language/language_pl.h
+++ b/Marlin/src/lcd/language/language_pl.h
@ -26,7 +26,6 @@
 *
 * LCD Menu Messages
 * See also https://marlinfw.org/docs/development/lcd_language.html
- *
 */

 #define DISPLAY_CHARSET_ISO10646_PL
--- a/Marlin/src/lcd/language/language_pt.h
+++ b/Marlin/src/lcd/language/language_pt.h
@ -27,7 +27,6 @@
 *
 * LCD Menu Messages
 * See also https://marlinfw.org/docs/development/lcd_language.html
- *
 */

 #define DISPLAY_CHARSET_ISO10646_1
--- a/Marlin/src/lcd/language/language_pt_br.h
+++ b/Marlin/src/lcd/language/language_pt_br.h
@ -27,7 +27,6 @@
 *
 * LCD Menu Messages
 * See also https://marlinfw.org/docs/development/lcd_language.html
- *
 */
 namespace Language_pt_br {
  using namespace Language_en; // Inherit undefined strings from English
--- a/Marlin/src/lcd/language/language_ru.h
+++ b/Marlin/src/lcd/language/language_ru.h
@ -26,7 +26,6 @@
 *
 * LCD Menu Messages
 * See also https://marlinfw.org/docs/development/lcd_language.html
- *
 */
 #define DISPLAY_CHARSET_ISO10646_5

--- a/Marlin/src/lcd/language/language_sk.h
+++ b/Marlin/src/lcd/language/language_sk.h
@ -30,7 +30,6 @@
 *
 * Translated by Michal Holeš, Farma MaM
 * https://www.facebook.com/farmamam
- *
 */
 #define DISPLAY_CHARSET_ISO10646_SK

--- a/Marlin/src/lcd/language/language_test.h
+++ b/Marlin/src/lcd/language/language_test.h
@ -26,7 +26,6 @@
 *
 * LCD Menu Messages
 * See also https://marlinfw.org/docs/development/lcd_language.html
- *
 */

 // Select ONE of the following Mappers.
--- a/Marlin/src/lcd/language/language_tr.h
+++ b/Marlin/src/lcd/language/language_tr.h
@ -30,7 +30,6 @@
 * Bu çeviri dosyasındaki sorunlar ve düzeltmeler için iletişim;
 * Contact for issues and corrections in this translation file;
 * Yücel Temel - (info@elektromanyetix.com) - https://elektromanyetix.com/
- *
 */

 #define DISPLAY_CHARSET_ISO10646_TR
--- a/Marlin/src/lcd/language/language_uk.h
+++ b/Marlin/src/lcd/language/language_uk.h
@ -26,7 +26,6 @@
 *
 * LCD Menu Messages
 * See also https://marlinfw.org/docs/development/lcd_language.html
- *
 */

 #define DISPLAY_CHARSET_ISO10646_5
--- a/Marlin/src/lcd/language/language_vi.h
+++ b/Marlin/src/lcd/language/language_vi.h
@ -26,7 +26,6 @@
 *
 * LCD Menu Messages
 * See also https://marlinfw.org/docs/development/lcd_language.html
- *
 */
 namespace Language_vi {
  using namespace Language_en; // Inherit undefined strings from English
--- a/Marlin/src/lcd/language/language_zh_CN.h
+++ b/Marlin/src/lcd/language/language_zh_CN.h
@ -26,7 +26,6 @@
 *
 * LCD Menu Messages
 * See also https://marlinfw.org/docs/development/lcd_language.html
- *
 */
 namespace Language_zh_CN {
  using namespace Language_en;  // Inherit undefined strings from English
--- a/Marlin/src/lcd/language/language_zh_TW.h
+++ b/Marlin/src/lcd/language/language_zh_TW.h
@ -26,7 +26,6 @@
 *
 * LCD Menu Messages
 * See also https://marlinfw.org/docs/development/lcd_language.html
- *
 */
 namespace Language_zh_TW {
  using namespace Language_en;  // Inherit undefined strings from English
--- a/Marlin/src/lcd/menu/menu_filament.cpp
+++ b/Marlin/src/lcd/menu/menu_filament.cpp
@ -101,9 +101,7 @@ void _menu_temp_filament_op(const PauseMode mode, const int8_t extruder) {
 }

 /**
- *
 * "Change Filament" submenu
- *
 */
 #if E_STEPPERS > 1 || ENABLED(FILAMENT_LOAD_UNLOAD_GCODES)

--- a/Marlin/src/libs/least_squares_fit.cpp
+++ b/Marlin/src/libs/least_squares_fit.cpp
@ -29,7 +29,6 @@
 * it saves roughly 10K of program memory. It also does not require all of
 * coordinates to be present during the calculations. Each point can be
 * probed and then discarded.
- *
 */

 #include "../inc/MarlinConfig.h"
--- a/Marlin/src/libs/least_squares_fit.h
+++ b/Marlin/src/libs/least_squares_fit.h
@ -30,7 +30,6 @@
 * it saves roughly 10K of program memory.   And even better...  the data
 * fed into the algorithm does not need to all be present at the same time.
 * A point can be probed and its values fed into the algorithm and then discarded.
- *
 */

 #include "../inc/MarlinConfig.h"
--- a/Marlin/src/module/planner.cpp
+++ b/Marlin/src/module/planner.cpp
@ -339,7 +339,6 @@ void Planner::init() {
     *  const uint32_t r = _BV(24) - x * d;                             // Estimate remainder
     *  if (r >= d) x++;                                                // Check whether to adjust result
     *  return uint32_t(x);                                             // x holds the proper estimation
-     *
     */
    static uint32_t get_period_inverse(uint32_t d) {

@ -2243,7 +2242,6 @@ bool Planner::_populate_block(block_t * const block, bool split_move,
      #define MAX_E_JERK(N) TERN(HAS_LINEAR_E_JERK, max_e_jerk[E_INDEX_N(N)], max_jerk.e)

      /**
-       *
       * Use LIN_ADVANCE for blocks if all these are true:
       *
       * esteps             : This is a print move, because we checked for A, B, C steps before.
--- a/Marlin/src/module/planner_bezier.cpp
+++ b/Marlin/src/module/planner_bezier.cpp
@ -24,7 +24,6 @@
 * planner_bezier.cpp
 *
 * Compute and buffer movement commands for bezier curves
- *
 */

 #include "../inc/MarlinConfig.h"
--- a/Marlin/src/module/planner_bezier.h
+++ b/Marlin/src/module/planner_bezier.h
@ -25,7 +25,6 @@
 * planner_bezier.h
 *
 * Compute and buffer movement commands for Bézier curves
- *
 */

 #include "../core/types.h"
--- a/Marlin/src/module/probe.cpp
+++ b/Marlin/src/module/probe.cpp
@ -729,7 +729,6 @@ float Probe::probe_at_point(const float &rx, const float &ry, const ProbePtRaise
     * when starting up the machine or rebooting the board.
     * There's no way to know where the nozzle is positioned until
     * homing has been done - no homing with z-probe without init!
-     *
     */
    STOW_Z_SERVO();
  }
--- a/Marlin/src/module/settings.cpp
+++ b/Marlin/src/module/settings.cpp
@ -33,7 +33,6 @@
 * ALSO: Variables in the Store and Retrieve sections must be in the same order.
 *       If a feature is disabled, some data must still be written that, when read,
 *       either sets a Sane Default, or results in No Change to the existing value.
- *
 */

 // Change EEPROM version if the structure changes
--- a/Marlin/src/module/thermistor/thermistor_30.h
+++ b/Marlin/src/module/thermistor/thermistor_30.h
@ -26,11 +26,11 @@
 // Resistance Tolerance     + / -1%
 // B Value             3950K at 25/50 deg. C
 // B Value Tolerance         + / - 1%
-// Kis3d Silicone Heater 24V 200W/300W with 6mm Precision cast plate (EN AW 5083) 
+// Kis3d Silicone Heater 24V 200W/300W with 6mm Precision cast plate (EN AW 5083)
 // Temperature setting time 10 min to determine the 12Bit ADC value on the surface. (le3tspeak)
 const temp_entry_t temptable_30[] PROGMEM = {
-  { OV(   1), 938 }, 
-  { OV( 298), 125 }, // 1193 - 125° 
+  { OV(   1), 938 },
+  { OV( 298), 125 }, // 1193 - 125°
  { OV( 321), 121 }, // 1285 - 121°
  { OV( 348), 117 }, // 1392 - 117°
  { OV( 387), 113 }, // 1550 - 113°
--- a/Marlin/src/pins/lpc1768/pins_BIQU_B300_V1.0.h
+++ b/Marlin/src/pins/lpc1768/pins_BIQU_B300_V1.0.h
@ -27,7 +27,6 @@
 * Applies to the following boards:
 *
 *  BOARD_BIQU_BQ111_A4 (Hotend, Fan, Bed)
- *
 */

 #if NOT_TARGET(MCU_LPC1768)
--- a/Marlin/src/pins/lpc1768/pins_BIQU_BQ111_A4.h
+++ b/Marlin/src/pins/lpc1768/pins_BIQU_BQ111_A4.h
@ -27,7 +27,6 @@
 * Applies to the following boards:
 *
 *  BOARD_BIQU_BQ111_A4 (Hotend, Fan, Bed)
- *
 */

 #if NOT_TARGET(MCU_LPC1768)
--- a/Marlin/src/pins/lpc1768/pins_MKS_SBASE.h
+++ b/Marlin/src/pins/lpc1768/pins_MKS_SBASE.h
@ -372,7 +372,6 @@
 *   P1_31 - not 5V tolerant - EXP1
 *   P0_27 - open collector  - EXP2
 *   P0_28 - open collector  - EXP2
- *
 */

 /**
@ -387,5 +386,4 @@
 *   P0_03 - AUX1
 *   P0_29 - Port -1
 *   P0_30 - USB
- *
 */
--- a/Marlin/src/pins/lpc1768/pins_RAMPS_RE_ARM.h
+++ b/Marlin/src/pins/lpc1768/pins_RAMPS_RE_ARM.h
@ -31,7 +31,6 @@
 *  RAMPS_14_EFF (Hotend, Fan0, Fan1)
 *  RAMPS_14_EEF (Hotend0, Hotend1, Fan)
 *  RAMPS_14_SF  (Spindle, Controller Fan)
- *
 */

 // Numbers in parentheses () are the corresponding mega2560 pin numbers
--- a/Marlin/src/pins/lpc1769/pins_BTT_SKR_E3_TURBO.h
+++ b/Marlin/src/pins/lpc1769/pins_BTT_SKR_E3_TURBO.h
@ -16,7 +16,7 @@
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
 *
 */
 #pragma once
--- a/Marlin/src/pins/lpc1769/pins_MKS_SGEN.h
+++ b/Marlin/src/pins/lpc1769/pins_MKS_SGEN.h
@ -26,7 +26,6 @@
 *
 * The pins diagram can be found and the following URL:
 * https://github.com/makerbase-mks/MKS-SGen/blob/master/Hardware/MKS%20SGEN%20V1.0_001/MKS%20SGEN%20V1.0_001%20PIN.pdf
- *
 */

 #if NOT_TARGET(MCU_LPC1769)
--- a/Marlin/src/pins/lpc1769/pins_TH3D_EZBOARD.h
+++ b/Marlin/src/pins/lpc1769/pins_TH3D_EZBOARD.h
@ -166,7 +166,6 @@
 *
 * A remote SD card is currently not supported because the pins routed to the EXP2
 * connector are shared with the onboard SD card.
- *
 */

 #if ENABLED(CR10_STOCKDISPLAY)
--- a/Marlin/src/pins/mega/pins_INTAMSYS40.h
+++ b/Marlin/src/pins/mega/pins_INTAMSYS40.h
@ -137,7 +137,6 @@
 ///////////////////// SPARE HEADERS //////////////

 /**
- *
 * J25
 * 1 D54
 * 2 D55
--- a/Marlin/src/pins/mega/pins_MINITRONICS.h
+++ b/Marlin/src/pins/mega/pins_MINITRONICS.h
@ -29,7 +29,6 @@
 * Rev B   2 JAN 2017
 *
 *  Added pin definitions for M3, M4 & M5 spindle control commands
- *
 */

 #if NOT_TARGET(__AVR_ATmega1281__)
--- a/Marlin/src/pins/pinsDebug.h
+++ b/Marlin/src/pins/pinsDebug.h
@ -31,7 +31,6 @@
 *
 *  Both passes use the same pin list.  The list contains two macro names. The
 *  actual macro definitions are changed depending on which pass is being done.
- *
 */

 // first pass - put the name strings into FLASH
--- a/Marlin/src/pins/ramps/pins_RAMPS_13.h
+++ b/Marlin/src/pins/ramps/pins_RAMPS_13.h
@ -31,7 +31,6 @@
 *  RAMPS_13_EFF (Extruder, Fan, Fan)
 *  RAMPS_13_EEF (Extruder, Extruder, Fan)
 *  RAMPS_13_SF  (Spindle, Controller Fan)
- *
 */

 #ifndef BOARD_INFO_NAME