Marlin 2.0 for Flying Bear 4S/5
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.

434 lines
14 KiB

/**
* Marlin 3D Printer Firmware
* Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
//
// Configuration Menu
//
#include "../../inc/MarlinConfigPre.h"
#if HAS_LCD_MENU
#include "menu.h"
#include "../../module/configuration_store.h"
#if HAS_FILAMENT_SENSOR
#include "../../feature/runout.h"
#endif
#if ENABLED(POWER_LOSS_RECOVERY)
#include "../../feature/power_loss_recovery.h"
#endif
#if HAS_BED_PROBE
#include "../../module/probe.h"
#if ENABLED(BLTOUCH)
#include "../../feature/bltouch.h"
#endif
#endif
#define HAS_DEBUG_MENU ENABLED(LCD_PROGRESS_BAR_TEST)
void menu_advanced_settings();
#if EITHER(DELTA_CALIBRATION_MENU, DELTA_AUTO_CALIBRATION)
void menu_delta_calibrate();
#endif
static void lcd_factory_settings() {
settings.reset();
#if HAS_BUZZER
ui.completion_feedback();
#endif
}
#if ENABLED(LCD_PROGRESS_BAR_TEST)
#include "../lcdprint.h"
static void progress_bar_test() {
static int8_t bar_percent = 0;
if (ui.use_click()) {
ui.goto_previous_screen();
ui.set_custom_characters(CHARSET_MENU);
return;
}
bar_percent += (int8_t)ui.encoderPosition;
LIMIT(bar_percent, 0, 100);
ui.encoderPosition = 0;
draw_menu_item_static(0, PSTR(MSG_PROGRESS_BAR_TEST), SS_CENTER|SS_INVERT);
lcd_put_int((LCD_WIDTH) / 2 - 2, LCD_HEIGHT - 2, bar_percent); lcd_put_wchar('%');
lcd_moveto(0, LCD_HEIGHT - 1); ui.draw_progress_bar(bar_percent);
}
void _progress_bar_test() {
ui.goto_screen(progress_bar_test);
ui.set_custom_characters(CHARSET_INFO);
}
#endif // LCD_PROGRESS_BAR_TEST
#if HAS_DEBUG_MENU
void menu_debug() {
START_MENU();
BACK_ITEM(MSG_CONFIGURATION);
#if ENABLED(LCD_PROGRESS_BAR_TEST)
SUBMENU(MSG_PROGRESS_BAR_TEST, _progress_bar_test);
#endif
END_MENU();
}
#endif
#if EXTRUDERS > 1
#include "../../module/tool_change.h"
void menu_tool_change() {
START_MENU();
BACK_ITEM(MSG_CONFIGURATION);
#if ENABLED(TOOLCHANGE_FILAMENT_SWAP)
static constexpr float max_extrude =
#if ENABLED(PREVENT_LENGTHY_EXTRUDE)
EXTRUDE_MAXLENGTH
#else
500
#endif
;
EDIT_ITEM(float3, MSG_FILAMENT_SWAP_LENGTH, &toolchange_settings.swap_length, 0, max_extrude);
EDIT_ITEM(float3, MSG_FILAMENT_PURGE_LENGTH, &toolchange_settings.extra_prime, 0, max_extrude);
EDIT_ITEM_FAST(int4, MSG_SINGLENOZZLE_RETRACT_SPD, &toolchange_settings.retract_speed, 10, 5400);
EDIT_ITEM_FAST(int4, MSG_SINGLENOZZLE_PRIME_SPD, &toolchange_settings.prime_speed, 10, 5400);
#endif
EDIT_ITEM(float3, MSG_TOOL_CHANGE_ZLIFT, &toolchange_settings.z_raise, 0, 10);
END_MENU();
}
#endif
#if HAS_HOTEND_OFFSET
#include "../../module/motion.h"
#include "../../gcode/queue.h"
void menu_tool_offsets() {
auto _recalc_offsets = []{
if (active_extruder && all_axes_known()) { // For the 2nd extruder re-home so the next tool-change gets the new offsets.
queue.inject_P(PSTR("G28")); // In future, we can babystep the 2nd extruder (if active), making homing unnecessary.
active_extruder = 0;
}
};
START_MENU();
BACK_ITEM(MSG_CONFIGURATION);
#if ENABLED(DUAL_X_CARRIAGE)
EDIT_ITEM_FAST(float51, MSG_X_OFFSET, &hotend_offset[1].x, float(X2_HOME_POS - 25), float(X2_HOME_POS + 25), _recalc_offsets);
#else
EDIT_ITEM_FAST(float52sign, MSG_X_OFFSET, &hotend_offset[1].x, -99.0, 99.0, _recalc_offsets);
#endif
EDIT_ITEM_FAST(float52sign, MSG_Y_OFFSET, &hotend_offset[1].y, -99.0, 99.0, _recalc_offsets);
EDIT_ITEM_FAST(float52sign, MSG_Z_OFFSET, &hotend_offset[1].z, Z_PROBE_LOW_POINT, 10.0, _recalc_offsets);
#if ENABLED(EEPROM_SETTINGS)
ACTION_ITEM(MSG_STORE_EEPROM, lcd_store_settings);
#endif
END_MENU();
}
#endif
#if ENABLED(DUAL_X_CARRIAGE)
void menu_idex() {
START_MENU();
BACK_ITEM(MSG_CONFIGURATION);
GCODES_ITEM(MSG_IDEX_MODE_AUTOPARK, PSTR("M605 S1\nG28 X\nG1 X100"));
const bool need_g28 = !(TEST(axis_known_position, Y_AXIS) && TEST(axis_known_position, Z_AXIS));
GCODES_ITEM(MSG_IDEX_MODE_DUPLICATE, need_g28
? PSTR("M605 S1\nT0\nG28\nM605 S2 X200\nG28 X\nG1 X100") // If Y or Z is not homed, do a full G28 first
: PSTR("M605 S1\nT0\nM605 S2 X200\nG28 X\nG1 X100")
);
GCODES_ITEM(MSG_IDEX_MODE_MIRRORED_COPY, need_g28
? PSTR("M605 S1\nT0\nG28\nM605 S2 X200\nG28 X\nG1 X100\nM605 S3 X200") // If Y or Z is not homed, do a full G28 first
: PSTR("M605 S1\nT0\nM605 S2 X200\nG28 X\nG1 X100\nM605 S3 X200")
);
GCODES_ITEM(MSG_IDEX_MODE_FULL_CTRL, PSTR("M605 S0\nG28 X"));
END_MENU();
}
#endif
#if ENABLED(BLTOUCH)
#if ENABLED(BLTOUCH_LCD_VOLTAGE_MENU)
void bltouch_report() {
SERIAL_ECHOLNPAIR("EEPROM Last BLTouch Mode - ", (int)bltouch.last_written_mode);
SERIAL_ECHOLNPGM("Configuration BLTouch Mode - "
#if ENABLED(BLTOUCH_SET_5V_MODE)
"5V"
#else
"OD"
#endif
);
char mess[21];
strcpy_P(mess, PSTR("BLTouch Mode - "));
strcpy_P(&mess[15], bltouch.last_written_mode ? PSTR("5V") : PSTR("OD"));
ui.set_status(mess);
ui.return_to_status();
}
#endif
void menu_bltouch() {
START_MENU();
BACK_ITEM(MSG_CONFIGURATION);
ACTION_ITEM(MSG_BLTOUCH_RESET, bltouch._reset);
ACTION_ITEM(MSG_BLTOUCH_SELFTEST, bltouch._selftest);
ACTION_ITEM(MSG_BLTOUCH_DEPLOY, bltouch._deploy);
ACTION_ITEM(MSG_BLTOUCH_STOW, bltouch._stow);
ACTION_ITEM(MSG_BLTOUCH_SW_MODE, bltouch._set_SW_mode);
#if ENABLED(BLTOUCH_LCD_VOLTAGE_MENU)
SUBMENU(MSG_BLTOUCH_5V_MODE, []{
do_select_screen(PSTR(MSG_BLTOUCH_5V_MODE), PSTR(MSG_BUTTON_CANCEL), bltouch._set_5V_mode, ui.goto_previous_screen, PSTR(MSG_BLTOUCH_MODE_CHANGE));
});
SUBMENU(MSG_BLTOUCH_OD_MODE, []{
do_select_screen(PSTR(MSG_BLTOUCH_OD_MODE), PSTR(MSG_BUTTON_CANCEL), bltouch._set_OD_mode, ui.goto_previous_screen, PSTR(MSG_BLTOUCH_MODE_CHANGE));
});
ACTION_ITEM(MSG_BLTOUCH_MODE_STORE, bltouch._mode_store);
SUBMENU(MSG_BLTOUCH_MODE_STORE_5V, []{
do_select_screen(PSTR(MSG_BLTOUCH_MODE_STORE_5V), PSTR(MSG_BUTTON_CANCEL), bltouch.mode_conv_5V, ui.goto_previous_screen, PSTR(MSG_BLTOUCH_MODE_CHANGE));
});
SUBMENU(MSG_BLTOUCH_MODE_STORE_OD, []{
do_select_screen(PSTR(MSG_BLTOUCH_MODE_STORE_OD), PSTR(MSG_BUTTON_CANCEL), bltouch.mode_conv_OD, ui.goto_previous_screen, PSTR(MSG_BLTOUCH_MODE_CHANGE));
});
ACTION_ITEM(MSG_BLTOUCH_MODE_ECHO, bltouch_report);
#endif
END_MENU();
}
#endif
#if ENABLED(TOUCH_MI_PROBE)
void menu_touchmi() {
START_MENU();
ui.defer_status_screen();
BACK_ITEM(MSG_CONFIGURATION);
GCODES_ITEM(MSG_TOUCHMI_INIT, PSTR("M851 Z0\nG28\nG1 F200 Z0"));
SUBMENU(MSG_ZPROBE_ZOFFSET, lcd_babystep_zoffset);
GCODES_ITEM(MSG_TOUCHMI_SAVE, PSTR("M500\nG1 F200 Z10"));
GCODES_ITEM(MSG_TOUCHMI_ZTEST, PSTR("G28\nG1 F200 Z0"));
END_MENU();
}
#endif
#if ENABLED(CASE_LIGHT_MENU)
#include "../../feature/caselight.h"
#if DISABLED(CASE_LIGHT_NO_BRIGHTNESS)
void menu_case_light() {
START_MENU();
BACK_ITEM(MSG_CONFIGURATION);
EDIT_ITEM(uint8, MSG_CASE_LIGHT_BRIGHTNESS, &case_light_brightness, 0, 255, update_case_light, true);
EDIT_ITEM(bool, MSG_CASE_LIGHT, (bool*)&case_light_on, update_case_light);
END_MENU();
}
#endif
#endif
#if ENABLED(FWRETRACT)
#include "../../feature/fwretract.h"
void menu_config_retract() {
START_MENU();
BACK_ITEM(MSG_CONFIGURATION);
#if ENABLED(FWRETRACT_AUTORETRACT)
EDIT_ITEM(bool, MSG_AUTORETRACT, &fwretract.autoretract_enabled, fwretract.refresh_autoretract);
#endif
EDIT_ITEM(float52sign, MSG_CONTROL_RETRACT, &fwretract.settings.retract_length, 0, 100);
#if EXTRUDERS > 1
EDIT_ITEM(float52sign, MSG_CONTROL_RETRACT_SWAP, &fwretract.settings.swap_retract_length, 0, 100);
#endif
EDIT_ITEM(float3, MSG_CONTROL_RETRACTF, &fwretract.settings.retract_feedrate_mm_s, 1, 999);
EDIT_ITEM(float52sign, MSG_CONTROL_RETRACT_ZHOP, &fwretract.settings.retract_zraise, 0, 999);
EDIT_ITEM(float52sign, MSG_CONTROL_RETRACT_RECOVER, &fwretract.settings.retract_recover_extra, -100, 100);
#if EXTRUDERS > 1
EDIT_ITEM(float52sign, MSG_CONTROL_RETRACT_RECOVER_SWAP, &fwretract.settings.swap_retract_recover_extra, -100, 100);
#endif
EDIT_ITEM(float3, MSG_CONTROL_RETRACT_RECOVERF, &fwretract.settings.retract_recover_feedrate_mm_s, 1, 999);
#if EXTRUDERS > 1
EDIT_ITEM(float3, MSG_CONTROL_RETRACT_RECOVER_SWAPF, &fwretract.settings.swap_retract_recover_feedrate_mm_s, 1, 999);
#endif
END_MENU();
}
#endif
#if DISABLED(SLIM_LCD_MENUS)
void _menu_configuration_preheat_settings(const uint8_t material) {
#if HOTENDS > 5
#define MINTEMP_ALL _MIN(HEATER_0_MINTEMP, HEATER_1_MINTEMP, HEATER_2_MINTEMP, HEATER_3_MINTEMP, HEATER_4_MINTEMP, HEATER_5_MINTEMP)
#define MAXTEMP_ALL _MAX(HEATER_0_MAXTEMP, HEATER_1_MAXTEMP, HEATER_2_MAXTEMP, HEATER_3_MAXTEMP, HEATER_4_MAXTEMP, HEATER_5_MAXTEMP)
#elif HOTENDS > 4
#define MINTEMP_ALL _MIN(HEATER_0_MINTEMP, HEATER_1_MINTEMP, HEATER_2_MINTEMP, HEATER_3_MINTEMP, HEATER_4_MINTEMP)
#define MAXTEMP_ALL _MAX(HEATER_0_MAXTEMP, HEATER_1_MAXTEMP, HEATER_2_MAXTEMP, HEATER_3_MAXTEMP, HEATER_4_MAXTEMP)
#elif HOTENDS > 3
#define MINTEMP_ALL _MIN(HEATER_0_MINTEMP, HEATER_1_MINTEMP, HEATER_2_MINTEMP, HEATER_3_MINTEMP)
#define MAXTEMP_ALL _MAX(HEATER_0_MAXTEMP, HEATER_1_MAXTEMP, HEATER_2_MAXTEMP, HEATER_3_MAXTEMP)
#elif HOTENDS > 2
#define MINTEMP_ALL _MIN(HEATER_0_MINTEMP, HEATER_1_MINTEMP, HEATER_2_MINTEMP)
#define MAXTEMP_ALL _MAX(HEATER_0_MAXTEMP, HEATER_1_MAXTEMP, HEATER_2_MAXTEMP)
#elif HOTENDS > 1
#define MINTEMP_ALL _MIN(HEATER_0_MINTEMP, HEATER_1_MINTEMP)
#define MAXTEMP_ALL _MAX(HEATER_0_MAXTEMP, HEATER_1_MAXTEMP)
#else
#define MINTEMP_ALL HEATER_0_MINTEMP
#define MAXTEMP_ALL HEATER_0_MAXTEMP
#endif
START_MENU();
BACK_ITEM(MSG_CONFIGURATION);
EDIT_ITEM(percent, MSG_FAN_SPEED, &ui.preheat_fan_speed[material], 0, 255);
#if HAS_TEMP_HOTEND
EDIT_ITEM(int3, MSG_NOZZLE, &ui.preheat_hotend_temp[material], MINTEMP_ALL, MAXTEMP_ALL - 15);
#endif
#if HAS_HEATED_BED
EDIT_ITEM(int3, MSG_BED, &ui.preheat_bed_temp[material], BED_MINTEMP, BED_MAXTEMP - 10);
#endif
#if ENABLED(EEPROM_SETTINGS)
ACTION_ITEM(MSG_STORE_EEPROM, lcd_store_settings);
#endif
END_MENU();
}
void menu_preheat_material1_settings() { _menu_configuration_preheat_settings(0); }
void menu_preheat_material2_settings() { _menu_configuration_preheat_settings(1); }
#endif
void menu_configuration() {
START_MENU();
BACK_ITEM(MSG_MAIN);
//
// Debug Menu when certain options are enabled
//
#if HAS_DEBUG_MENU
SUBMENU(MSG_DEBUG_MENU, menu_debug);
#endif
SUBMENU(MSG_ADVANCED_SETTINGS, menu_advanced_settings);
#if ENABLED(BABYSTEP_ZPROBE_OFFSET)
SUBMENU(MSG_ZPROBE_ZOFFSET, lcd_babystep_zoffset);
#elif HAS_BED_PROBE
EDIT_ITEM(float52, MSG_ZPROBE_ZOFFSET, &probe_offset.z, Z_PROBE_OFFSET_RANGE_MIN, Z_PROBE_OFFSET_RANGE_MAX);
#endif
const bool busy = printer_busy();
if (!busy) {
//
// Delta Calibration
//
#if EITHER(DELTA_CALIBRATION_MENU, DELTA_AUTO_CALIBRATION)
SUBMENU(MSG_DELTA_CALIBRATE, menu_delta_calibrate);
#endif
#if HAS_HOTEND_OFFSET
SUBMENU(MSG_OFFSETS_MENU, menu_tool_offsets);
#endif
#if ENABLED(DUAL_X_CARRIAGE)
SUBMENU(MSG_IDEX_MENU, menu_idex);
#endif
#if ENABLED(BLTOUCH)
SUBMENU(MSG_BLTOUCH, menu_bltouch);
#endif
#if ENABLED(TOUCH_MI_PROBE)
SUBMENU(MSG_TOUCHMI_PROBE, menu_touchmi);
#endif
}
//
// Set single nozzle filament retract and prime length
//
#if EXTRUDERS > 1
SUBMENU(MSG_TOOL_CHANGE, menu_tool_change);
#endif
//
// Set Case light on/off/brightness
//
#if ENABLED(CASE_LIGHT_MENU)
#if DISABLED(CASE_LIGHT_NO_BRIGHTNESS)
if (PWM_PIN(CASE_LIGHT_PIN))
SUBMENU(MSG_CASE_LIGHT, menu_case_light);
else
#endif
EDIT_ITEM(bool, MSG_CASE_LIGHT, (bool*)&case_light_on, update_case_light);
#endif
#if HAS_LCD_CONTRAST
EDIT_ITEM(int3, MSG_CONTRAST, &ui.contrast, LCD_CONTRAST_MIN, LCD_CONTRAST_MAX, ui.refresh_contrast, true);
#endif
#if ENABLED(FWRETRACT)
SUBMENU(MSG_RETRACT, menu_config_retract);
#endif
#if HAS_FILAMENT_SENSOR
EDIT_ITEM(bool, MSG_RUNOUT_SENSOR, &runout.enabled, runout.reset);
#endif
#if ENABLED(POWER_LOSS_RECOVERY)
EDIT_ITEM(bool, MSG_OUTAGE_RECOVERY, &recovery.enabled, recovery.changed);
#endif
#if DISABLED(SLIM_LCD_MENUS)
// Preheat configurations
SUBMENU(MSG_PREHEAT_1_SETTINGS, menu_preheat_material1_settings);
SUBMENU(MSG_PREHEAT_2_SETTINGS, menu_preheat_material2_settings);
#endif
#if ENABLED(EEPROM_SETTINGS)
ACTION_ITEM(MSG_STORE_EEPROM, lcd_store_settings);
if (!busy)
ACTION_ITEM(MSG_LOAD_EEPROM, lcd_load_settings);
#endif
if (!busy)
ACTION_ITEM(MSG_RESTORE_FAILSAFE, lcd_factory_settings);
END_MENU();
}
#endif // HAS_LCD_MENU