Marlin 2.0 for Flying Bear 4S/5
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.

202 lines
5.3 KiB

/**
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* Sanguinololu board pin assignments
*/
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega1284P__)
#error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu."
#endif
#ifndef BOARD_NAME
#define BOARD_NAME "Sanguinololu <1.2"
#endif
#define IS_MELZI (MB(MELZI) || MB(MELZI_MAKR3D))
//
// Limit Switches
//
#define X_STOP_PIN 18
#define Y_STOP_PIN 19
#define Z_STOP_PIN 20
//
// Z Probe (when not Z_MIN_PIN)
//
#if ENABLED(Z_PROBE_SLED)
#define SLED_PIN -1
#endif
//
// Steppers
//
#define X_STEP_PIN 15
#define X_DIR_PIN 21
#define Y_STEP_PIN 22
#define Y_DIR_PIN 23
#define Z_STEP_PIN 3
#define Z_DIR_PIN 2
#define E0_STEP_PIN 1
#define E0_DIR_PIN 0
//
// Temperature Sensors
//
#define TEMP_0_PIN 7 // Analog Input (pin 33 extruder)
#define TEMP_BED_PIN 6 // Analog Input (pin 34 bed)
//
// Heaters / Fans
//
#define HEATER_0_PIN 13 // (extruder)
#if ENABLED(SANGUINOLOLU_V_1_2)
#define HEATER_BED_PIN 12 // (bed)
#define X_ENABLE_PIN 14
#define Y_ENABLE_PIN 14
#define Z_ENABLE_PIN 26
#define E0_ENABLE_PIN 14
#if ENABLED(LCD_I2C_PANELOLU2)
#define FAN_PIN 4 // Uses Transistor1 (PWM) on Panelolu2's Sanguino Adapter Board to drive the fan
#endif
#else
#define HEATER_BED_PIN 14 // (bed)
#define X_ENABLE_PIN -1
#define Y_ENABLE_PIN -1
#define Z_ENABLE_PIN -1
#define E0_ENABLE_PIN -1
#endif
#if MB(AZTEEG_X1) || MB(STB_11) || IS_MELZI
#define FAN_PIN 4 // Works for Panelolu2 too
#endif
//
// Misc. Functions
//
/**
* On some broken versions of the Sanguino libraries the pin definitions are wrong,
* which then needs SDSS as pin 24. But you should upgrade your Sanguino libraries! See #368.
*/
//#define SDSS 24
#define SDSS 31
#if IS_MELZI
#define LED_PIN 27 // On some broken versions of the Sanguino libraries the pin definitions are wrong, so LED_PIN needs to be 28. But you should upgrade your Sanguino libraries! See #368.
#elif MB(STB_11)
#define LCD_BACKLIGHT_PIN 17 // LCD backlight LED
#endif
//
// LCD / Controller
//
#if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)
#if ENABLED(DOGLCD)
#if ENABLED(U8GLIB_ST7920) // SPI GLCD 12864 ST7920 ( like [www.digole.com] ) For Melzi V2.0
#if IS_MELZI // Melzi board
#define LCD_PINS_RS 30 // CS chip select /SS chip slave select
#define LCD_PINS_ENABLE 29 // SID (MOSI)
#define LCD_PINS_D4 17 // SCK (CLK) clock
// Pin 27 is taken by LED_PIN, but Melzi LED does nothing with
// Marlin so this can be used for BEEPER_PIN. You can use this pin
// with M42 instead of BEEPER_PIN.
#define BEEPER_PIN 27
#else // Sanguinololu 1.3
#define LCD_PINS_RS 4
#define LCD_PINS_ENABLE 17
#define LCD_PINS_D4 30
#define LCD_PINS_D5 29
#define LCD_PINS_D6 28
#define LCD_PINS_D7 27
#endif
#else // DOGM SPI LCD Support
#define DOGLCD_A0 30
#define LCD_CONTRAST 1
#if ENABLED(MAKRPANEL)
#define BEEPER_PIN 29
#define DOGLCD_CS 17
#define LCD_BACKLIGHT_PIN 28 // PA3
#else // !MAKRPANEL
#define DOGLCD_CS 29
#endif
#endif
// Uncomment screen orientation
#define LCD_SCREEN_ROT_0
9 years ago
//#define LCD_SCREEN_ROT_90
//#define LCD_SCREEN_ROT_180
//#define LCD_SCREEN_ROT_270
#else // !DOGLCD
#define LCD_PINS_RS 4
#define LCD_PINS_ENABLE 17
#define LCD_PINS_D4 30
#define LCD_PINS_D5 29
#define LCD_PINS_D6 28
#define LCD_PINS_D7 27
#endif // !DOGLCD
#define BTN_EN1 11
#define BTN_EN2 10
#if ENABLED(LCD_I2C_PANELOLU2)
#if IS_MELZI
#define BTN_ENC 29
#define LCD_SDSS 30 // Panelolu2 SD card reader rather than the Melzi
#else
#define BTN_ENC 30
#endif
#elif ENABLED(OLED_PANEL_TINYBOY2)
#define BTN_ENC 28
#define LCD_SDSS -1
#else // !Panelolu2, !TinyBoy2
#define BTN_ENC 16
#define LCD_SDSS 28 // Smart Controller SD card reader rather than the Melzi
#endif // !Panelolu2, !TinyBoy2
#define SD_DETECT_PIN -1
#endif // ULTRA_LCD && NEWPANEL