|
|
|
|
/**
|
|
|
|
|
* RIGIDBOARD Arduino Mega with RAMPS v1.3 pin assignments
|
|
|
|
|
*/
|
|
|
|
|
|
|
|
|
|
#include "pins_RAMPS_13.h"
|
|
|
|
|
|
|
|
|
|
#if ENABLED(Z_PROBE_ENDSTOP)
|
|
|
|
|
#define Z_PROBE_PIN 19
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#undef HEATER_0_PIN
|
|
|
|
|
#undef HEATER_1_PIN
|
|
|
|
|
#define HEATER_0_PIN 9 // EXTRUDER 1
|
|
|
|
|
#define HEATER_1_PIN 12 // EXTRUDER 2 (FAN On Sprinter)
|
|
|
|
|
|
|
|
|
|
#undef TEMP_0_PIN
|
|
|
|
|
#undef TEMP_1_PIN
|
|
|
|
|
#define TEMP_0_PIN 14 // ANALOG NUMBERING
|
|
|
|
|
#define TEMP_1_PIN 13 // ANALOG NUMBERING
|
|
|
|
|
|
|
|
|
|
// LCD Panel options for the RigidBoard
|
|
|
|
|
|
|
|
|
|
#if ENABLED(RIGIDBOT_PANEL)
|
|
|
|
|
|
|
|
|
|
#undef BEEPER_PIN
|
|
|
|
|
#define BEEPER_PIN -1
|
|
|
|
|
|
|
|
|
|
#undef SDCARDDETECT
|
|
|
|
|
#define SDCARDDETECT 22
|
|
|
|
|
|
|
|
|
|
// Extra button definitions, substitute for EN1 / EN2
|
|
|
|
|
#define BTN_UP 37 // BTN_EN1
|
|
|
|
|
#define BTN_DWN 35 // BTN_EN2
|
|
|
|
|
#define BTN_LFT 33
|
|
|
|
|
#define BTN_RT 32
|
|
|
|
|
|
|
|
|
|
// Marlin can respond to UP/DOWN by default
|
|
|
|
|
// #undef BTN_EN1
|
|
|
|
|
// #undef BTN_EN2
|
|
|
|
|
// #define BTN_EN1 -1
|
|
|
|
|
// #define BTN_EN2 -1
|
|
|
|
|
|
|
|
|
|
#undef BTN_ENC
|
|
|
|
|
#define BTN_ENC 31
|
|
|
|
|
|
|
|
|
|
#undef SDCARDDETECT
|
|
|
|
|
#define SDCARDDETECT 22
|
|
|
|
|
|
|
|
|
|
#elif defined(REPRAP_DISCOUNT_SMART_CONTROLLER)
|
|
|
|
|
|
|
|
|
|
#undef BEEPER_PIN
|
|
|
|
|
#define BEEPER_PIN -1
|
|
|
|
|
|
|
|
|
|
#undef SDCARDDETECT
|
|
|
|
|
#define SDCARDDETECT 22
|
|
|
|
|
|
|
|
|
|
#undef KILL_PIN
|
|
|
|
|
#define KILL_PIN 32
|
|
|
|
|
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
// SPI for Max6675 Thermocouple
|
|
|
|
|
#undef MAX6675_SS
|
|
|
|
|
#ifndef SDSUPPORT
|
|
|
|
|
#define MAX6675_SS 53 // Don't use pin 53 if there is even the remote possibility of using Display/SD card
|
|
|
|
|
#else
|
|
|
|
|
#define MAX6675_SS 49 // Don't use pin 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
// RigidBot swaps E0 / E1 plugs vs RAMPS 1.3
|
|
|
|
|
|
|
|
|
|
#undef E0_STEP_PIN
|
|
|
|
|
#undef E0_DIR_PIN
|
|
|
|
|
#undef E0_ENABLE_PIN
|
|
|
|
|
#define E0_STEP_PIN 36
|
|
|
|
|
#define E0_DIR_PIN 34
|
|
|
|
|
#define E0_ENABLE_PIN 30
|
|
|
|
|
|
|
|
|
|
#undef E1_STEP_PIN
|
|
|
|
|
#undef E1_DIR_PIN
|
|
|
|
|
#undef E1_ENABLE_PIN
|
|
|
|
|
#define E1_STEP_PIN 26
|
|
|
|
|
#define E1_DIR_PIN 28
|
|
|
|
|
#define E1_ENABLE_PIN 24
|
|
|
|
|
|
|
|
|
|
#undef FAN_PIN
|
|
|
|
|
#define FAN_PIN 8 // Same as RAMPS_13_EEF
|
|
|
|
|
|
|
|
|
|
#undef PS_ON_PIN
|
|
|
|
|
#define PS_ON_PIN -1
|
|
|
|
|
|
|
|
|
|
#undef HEATER_BED_PIN
|
|
|
|
|
#define HEATER_BED_PIN 10
|
|
|
|
|
|
|
|
|
|
#undef TEMP_BED_PIN
|
|
|
|
|
#define TEMP_BED_PIN 15 // ANALOG NUMBERING
|
|
|
|
|
|
|
|
|
|
#define STEPPER_RESET_PIN 41 // Stepper drivers have a reset on RigidBot
|
