|
|
|
|
/**
|
|
|
|
|
* Marlin 3D Printer Firmware
|
|
|
|
|
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
|
|
|
*
|
|
|
|
|
* Based on Sprinter and grbl.
|
|
|
|
|
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
|
|
|
|
*
|
|
|
|
|
* This program is free software: you can redistribute it and/or modify
|
|
|
|
|
* it under the terms of the GNU General Public License as published by
|
|
|
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
|
|
|
* (at your option) any later version.
|
|
|
|
|
*
|
|
|
|
|
* This program is distributed in the hope that it will be useful,
|
|
|
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
|
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
|
|
|
* GNU General Public License for more details.
|
|
|
|
|
*
|
|
|
|
|
* You should have received a copy of the GNU General Public License
|
|
|
|
|
* along with this program. If not, see <https://www.gnu.org/licenses/>.
|
|
|
|
|
*
|
|
|
|
|
*/
|
|
|
|
|
#pragma once
|
|
|
|
|
|
|
|
|
|
/**
|
|
|
|
|
* Pin assignments for the RUMBA32
|
|
|
|
|
*
|
|
|
|
|
* https://aus3d.com.au/rumba32
|
|
|
|
|
* https://github.com/Aus3D/RUMBA32
|
|
|
|
|
*/
|
|
|
|
|
|
|
|
|
|
#define BOARD_INFO_NAME "RUMBA32"
|
|
|
|
|
|
|
|
|
|
#if NO_EEPROM_SELECTED
|
|
|
|
|
#if MB(RUMBA32_V1_0)
|
|
|
|
|
#define FLASH_EEPROM_EMULATION
|
|
|
|
|
#define MARLIN_EEPROM_SIZE 0x1000 // 4K
|
|
|
|
|
#elif MB(RUMBA32_V1_1)
|
|
|
|
|
#define I2C_EEPROM
|
|
|
|
|
#define MARLIN_EEPROM_SIZE 0x2000 // 8K (24LC64T-I/OT)
|
|
|
|
|
#endif
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#if ENABLED(FLASH_EEPROM_EMULATION)
|
|
|
|
|
// Decrease delays and flash wear by spreading writes across the
|
|
|
|
|
// 128 kB sector allocated for EEPROM emulation.
|
|
|
|
|
#define FLASH_EEPROM_LEVELING
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#include "pins_RUMBA32_common.h"
|
|
|
|
|
|
|
|
|
|
#if MB(RUMBA32_V1_1)
|
|
|
|
|
|
|
|
|
|
#define SERVO0_PIN PA15
|
|
|
|
|
|
|
|
|
|
#if HAS_TMC_UART
|
|
|
|
|
//
|
|
|
|
|
// TMC2208/TMC2209 stepper drivers - Software Serial is used according to below pins
|
|
|
|
|
//
|
|
|
|
|
#define X_SERIAL_TX_PIN PA14
|
|
|
|
|
#define X_SERIAL_RX_PIN PC14
|
|
|
|
|
|
|
|
|
|
#define Y_SERIAL_TX_PIN PA13
|
|
|
|
|
#define Y_SERIAL_RX_PIN PE4
|
|
|
|
|
|
|
|
|
|
#define Z_SERIAL_TX_PIN PB10
|
|
|
|
|
#define Z_SERIAL_RX_PIN PE0
|
|
|
|
|
|
|
|
|
|
#define E0_SERIAL_TX_PIN PD11
|
|
|
|
|
#define E0_SERIAL_RX_PIN PC13
|
|
|
|
|
|
|
|
|
|
#define E1_SERIAL_TX_PIN PB3
|
|
|
|
|
#define E1_SERIAL_RX_PIN PD5
|
|
|
|
|
|
|
|
|
|
#define E2_SERIAL_TX_PIN PB4
|
|
|
|
|
#define E2_SERIAL_RX_PIN PD1
|
|
|
|
|
#endif
|
|
|
|
|
#endif
|
