# ifndef __CONFIGURATION_ADV_H
# define __CONFIGURATION_ADV_H
//===========================================================================
//=============================Thermal Settings ============================
//===========================================================================
// Select one of these only to define how the bed temp is read.
//
//#define BED_LIMIT_SWITCHING
# ifdef BED_LIMIT_SWITCHING
# define BED_HYSTERESIS 2 //only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS
# endif
# define BED_CHECK_INTERVAL 5000 //ms
//// Heating sanity check:
// This waits for the watchperiod in milliseconds whenever an M104 or M109 increases the target temperature
// If the temperature has not increased at the end of that period, the target temperature is set to zero.
// It can be reset with another M104/M109
//#define WATCHPERIOD 20000 //20 seconds
// Wait for Cooldown
// This defines if the M109 call should not block if it is cooling down.
// example: From a current temp of 220, you set M109 S200.
// if CooldownNoWait is defined M109 will not wait for the cooldown to finish
# define CooldownNoWait true
# ifdef PIDTEMP
// this adds an experimental additional term to the heatingpower, proportional to the extrusion speed.
// if Kc is choosen well, the additional required power due to increased melting should be compensated.
# define PID_ADD_EXTRUSION_RATE
# ifdef PID_ADD_EXTRUSION_RATE
# define DEFAULT_Kc (1) //heatingpower=Kc*(e_speed)
# endif
# endif
//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
//The maximum buffered steps/sec of the extruder motor are called "se".
//You enter the autotemp mode by a M109 S<mintemp> T<maxtemp> F<factor>
// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
// you exit the value by any M109 without F*
// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
// on an ultimaker, some initial testing worked with M109 S215 T260 F0.1 in the start.gcode
//#define AUTOTEMP
# ifdef AUTOTEMP
# define AUTOTEMP_OLDWEIGHT 0.98
# endif
// extruder run-out prevention.
//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
//#define EXTRUDER_RUNOUT_PREVENT
# define EXTRUDER_RUNOUT_MINTEMP 190
# define EXTRUDER_RUNOUT_SECONDS 30.
# define EXTRUDER_RUNOUT_ESTEPS 14. //mm filament
# define EXTRUDER_RUNOUT_SPEED 1500. //extrusion speed
# define EXTRUDER_RUNOUT_EXTRUDE 100
//These defines help to calibrate the AD595 sensor in case you get wrong temperature measurements.
//The measured temperature is defined as "actualTemp = (measuredTemp * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET"
# define TEMP_SENSOR_AD595_OFFSET 0.0
# define TEMP_SENSOR_AD595_GAIN 1.0
//This is for controlling a fan to cool down the stepper drivers
//it will turn on when any driver is enabled
//and turn off after the set amount of seconds from last driver being disabled again
//#define CONTROLLERFAN_PIN 23 //Pin used for the fan to cool controller, comment out to disable this function
# define CONTROLLERFAN_SEC 60 //How many seconds, after all motors were disabled, the fan should run
//===========================================================================
//=============================Mechanical Settings===========================
//===========================================================================
// This defines the number of extruders
# define EXTRUDERS 1
# define ENDSTOPS_ONLY_FOR_HOMING // If defined the endstops will only be used for homing
//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
# define X_HOME_RETRACT_MM 5
# define Y_HOME_RETRACT_MM 5
# define Z_HOME_RETRACT_MM 1
//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
# define AXIS_RELATIVE_MODES {false, false, false, false}
# define MAX_STEP_FREQUENCY 40000 // Max step frequency for Ultimaker (5000 pps / half step)
//default stepper release if idle
# define DEFAULT_STEPPER_DEACTIVE_TIME 60
# define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
# define DEFAULT_MINTRAVELFEEDRATE 0.0
// minimum time in microseconds that a movement needs to take if the buffer is emptied. Increase this number if you see blobs while printing high speed & high detail. It will slowdown on the detailed stuff.
# define DEFAULT_MINSEGMENTTIME 20000 // Obsolete delete this
// If defined the movements slow down when the look ahead buffer is only half full
# define SLOWDOWN
// Frequency limit
// See nophead's blog for more info
// Not working O
//#define XY_FREQUENCY_LIMIT 15
// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
// of the buffer and all stops. This should not be much greater than zero and should only be changed
// if unwanted behavior is observed on a user's machine when running at very slow speeds.
# define MINIMUM_PLANNER_SPEED 2.0 // (mm/sec)
//===========================================================================
//=============================Additional Features===========================
//===========================================================================
# define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
# define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // no z because of layer shift.
// The hardware watchdog should halt the Microcontroller, in case the firmware gets stuck somewhere. However:
// the Watchdog is not working well, so please only enable this for testing
// this enables the watchdog interrupt.
//#define USE_WATCHDOG
//#ifdef USE_WATCHDOG
// you cannot reboot on a mega2560 due to a bug in he bootloader. Hence, you have to reset manually, and this is done hereby:
//#define RESET_MANUAL
//#define WATCHDOG_TIMEOUT 4 //seconds
//#endif
// extruder advance constant (s2/mm3)
//
// advance (steps) = STEPS_PER_CUBIC_MM_E * EXTUDER_ADVANCE_K * cubic mm per second ^ 2
//
// hooke's law says: force = k * distance
// bernoulli's priniciple says: v ^ 2 / 2 + g . h + pressure / density = constant
// so: v ^ 2 is proportional to number of steps we advance the extruder
//#define ADVANCE
# ifdef ADVANCE
# define EXTRUDER_ADVANCE_K .0
# define D_FILAMENT 2.85
# define STEPS_MM_E 836
# define EXTRUTION_AREA (0.25 * D_FILAMENT * D_FILAMENT * 3.14159)
# define STEPS_PER_CUBIC_MM_E (axis_steps_per_unit[E_AXIS] / EXTRUTION_AREA)
# endif // ADVANCE
// A debugging feature to compare calculated vs performed steps, to see if steps are lost by the software.
//#define DEBUG_STEPS
// Arc interpretation settings:
# define MM_PER_ARC_SEGMENT 1
# define N_ARC_CORRECTION 25
const int dropsegments = 5 ; //everything with less than this number of steps will be ignored as move and joined with the next movement
// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
// in the pins.h file. When using a push button pulling the pin to ground this will need inverted. This setting should
// be commented out otherwise
# define SDCARDDETECTINVERTED
# ifdef ULTIPANEL
# undef SDCARDDETECTINVERTED
# endif
//===========================================================================
//=============================Buffers ============================
//===========================================================================
// The number of linear motions that can be in the plan at any give time.
// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ringbuffering.
# if defined SDSUPPORT
# define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
# else
# define BLOCK_BUFFER_SIZE 16 // maximize block buffer
# endif
//The ASCII buffer for recieving from the serial:
# define MAX_CMD_SIZE 96
# define BUFSIZE 4
//===========================================================================
//============================= Define Defines ============================
//===========================================================================
# if TEMP_SENSOR_0 > 0
# define THERMISTORHEATER_0 TEMP_SENSOR_0
# define HEATER_0_USES_THERMISTOR
# endif
# if TEMP_SENSOR_1 > 0
# define THERMISTORHEATER_1 TEMP_SENSOR_1
# define HEATER_1_USES_THERMISTOR
# endif
# if TEMP_SENSOR_2 > 0
# define THERMISTORHEATER_2 TEMP_SENSOR_2
# define HEATER_2_USES_THERMISTOR
# endif
# if TEMP_SENSOR_BED > 0
# define THERMISTORBED TEMP_SENSOR_BED
# define BED_USES_THERMISTOR
# endif
# if TEMP_SENSOR_0 == -1
# define HEATER_0_USES_AD595
# endif
# if TEMP_SENSOR_1 == -1
# define HEATER_1_USES_AD595
# endif
# if TEMP_SENSOR_2 == -1
# define HEATER_2_USES_AD595
# endif
# if TEMP_SENSOR_BED == -1
# define BED_USES_AD595
# endif
# if TEMP_SENSOR_0 == -2
# define HEATER_0_USES_MAX6675
# endif
# if TEMP_SENSOR_0 == 0
# undef HEATER_0_MINTEMP
# undef HEATER_0_MAXTEMP
# endif
# if TEMP_SENSOR_1 == 0
# undef HEATER_1_MINTEMP
# undef HEATER_1_MAXTEMP
# endif
# if TEMP_SENSOR_2 == 0
# undef HEATER_2_MINTEMP
# undef HEATER_2_MAXTEMP
# endif
# if TEMP_SENSOR_BED == 0
# undef BED_MINTEMP
# undef BED_MAXTEMP
# endif
# endif //__CONFIGURATION_ADV_H
