Marlin_FB4S/Marlin/pins_RUMBA.h

/**
 * RUMBA pin assignments
 */

#ifndef __AVR_ATmega2560__
  #error Oops!  Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
#endif

#if EXTRUDERS > 3
  #error RUMBA supports up to 3 extruders. Comment this line to keep going.
#endif

#define X_STEP_PIN         17
#define X_DIR_PIN          16
#define X_ENABLE_PIN       48
#define X_MIN_PIN          37
#define X_MAX_PIN          36

#define Y_STEP_PIN         54
#define Y_DIR_PIN          47
#define Y_ENABLE_PIN       55
#define Y_MIN_PIN          35
#define Y_MAX_PIN          34

#define Z_STEP_PIN         57
#define Z_DIR_PIN          56
#define Z_ENABLE_PIN       62
#define Z_MIN_PIN          33
#define Z_MAX_PIN          32
#define Z_MIN_PROBE_PIN    -1

#if ENABLED(Z_MIN_PROBE_ENDSTOP)
  // Define a pin to use as the signal pin on Arduino for the Z probe endstop.
  #define Z_MIN_PROBE_PIN  33
#endif

#define E0_STEP_PIN        23
#define E0_DIR_PIN         22
#define E0_ENABLE_PIN      24

#define E1_STEP_PIN        26
#define E1_DIR_PIN         25
#define E1_ENABLE_PIN      27

#define E2_STEP_PIN        29
#define E2_DIR_PIN         28
#define E2_ENABLE_PIN      39

#define LED_PIN            13

#define FAN_PIN             7
#define FAN1_PIN            8

#define PS_ON_PIN          45
#define KILL_PIN           46

#if TEMP_SENSOR_0 == 0
  #define TEMP_0_PIN           -1
  #define HEATER_0_PIN         -1
#else
  #define HEATER_0_PIN          2   // EXTRUDER 1
  #if TEMP_SENSOR_0 == -1
    #define TEMP_0_PIN          6   // ANALOG NUMBERING - connector *K1* on RUMBA thermocouple ADD ON is used
  #else
    #define TEMP_0_PIN         15   // ANALOG NUMBERING - default connector for thermistor *T0* on rumba board is used
  #endif
#endif

#if TEMP_SENSOR_1 == 0
  #define TEMP_1_PIN           -1
  #define HEATER_1_PIN         -1
#else
  #define HEATER_1_PIN          3   // EXTRUDER 2
  #if TEMP_SENSOR_1 == -1
    #define TEMP_1_PIN          5   // ANALOG NUMBERING - connector *K2* on RUMBA thermocouple ADD ON is used
  #else
    #define TEMP_1_PIN         14   // ANALOG NUMBERING - default connector for thermistor *T1* on rumba board is used
  #endif
#endif

#if TEMP_SENSOR_2 == 0
  #define TEMP_2_PIN          -1
  #define HEATER_2_PIN        -1
#else
  #define HEATER_2_PIN         6    // EXTRUDER 3
  #if TEMP_SENSOR_2 == -1
    #define TEMP_2_PIN         7    // ANALOG NUMBERING - connector *K3* on RUMBA thermocouple ADD ON is used <-- this can not be used when TEMP_SENSOR_BED is defined as thermocouple
  #else
    #define TEMP_2_PIN         13   // ANALOG NUMBERING - default connector for thermistor *T2* on rumba board is used
  #endif
#endif

//optional for extruder 4 or chamber: #define TEMP_X_PIN         12   // ANALOG NUMBERING - default connector for thermistor *T3* on rumba board is used
//optional FAN1 can be used as 4th heater output: #define HEATER_3_PIN       8    // EXTRUDER 4

#if TEMP_SENSOR_BED == 0
  #define TEMP_BED_PIN        -1
  #define HEATER_BED_PIN      -1
#else
  #define HEATER_BED_PIN       9    // BED
  #if TEMP_SENSOR_BED == -1
    #define TEMP_BED_PIN       7    // ANALOG NUMBERING - connector *K3* on RUMBA thermocouple ADD ON is used <-- this can not be used when TEMP_SENSOR_2 is defined as thermocouple
  #else
    #define TEMP_BED_PIN      11    // ANALOG NUMBERING - default connector for thermistor *THB* on rumba board is used
  #endif
#endif

#define SDPOWER            -1
#define SDSS               53
#define SD_DETECT_PIN      49
#define BEEPER_PIN         44
#define LCD_PINS_RS        19
#define LCD_PINS_ENABLE    42
#define LCD_PINS_D4        18
#define LCD_PINS_D5        38
#define LCD_PINS_D6        41
#define LCD_PINS_D7        40
#define BTN_EN1            11
#define BTN_EN2            12
#define BTN_ENC            43

#define SERVO0_PIN         5
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion…. 10 years ago			`/**`
			`* RUMBA pin assignments`
			`*/`

			`#ifndef __AVR_ATmega2560__`
			`#error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.`
			`#endif`

Cleanup of temperature code - Reduce calls to millis() - General cleanup of manage_heaters - General cleanup of pid autotune - Formatting here & there - Macros to clean up and shrink ISR code (reduced by ~364 lines) 10 years ago			`#if EXTRUDERS > 3`
			`#error RUMBA supports up to 3 extruders. Comment this line to keep going.`
			`#endif`

Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion…. 10 years ago			`#define X_STEP_PIN 17`
			`#define X_DIR_PIN 16`
			`#define X_ENABLE_PIN 48`
			`#define X_MIN_PIN 37`
			`#define X_MAX_PIN 36`

			`#define Y_STEP_PIN 54`
			`#define Y_DIR_PIN 47`
			`#define Y_ENABLE_PIN 55`
			`#define Y_MIN_PIN 35`
			`#define Y_MAX_PIN 34`

			`#define Z_STEP_PIN 57`
			`#define Z_DIR_PIN 56`
			`#define Z_ENABLE_PIN 62`
			`#define Z_MIN_PIN 33`
			`#define Z_MAX_PIN 32`
Some renaming of Z_PROBE to Z_MIN_PROBE (PR#91) * Fix a couple of renames omission and macro expansion errors. 9 years ago			`#define Z_MIN_PROBE_PIN -1`

			`#if ENABLED(Z_MIN_PROBE_ENDSTOP)`
			`// Define a pin to use as the signal pin on Arduino for the Z probe endstop.`
			`#define Z_MIN_PROBE_PIN 33`
			`#endif`
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion…. 10 years ago
			`#define E0_STEP_PIN 23`
			`#define E0_DIR_PIN 22`
			`#define E0_ENABLE_PIN 24`

			`#define E1_STEP_PIN 26`
			`#define E1_DIR_PIN 25`
			`#define E1_ENABLE_PIN 27`

			`#define E2_STEP_PIN 29`
			`#define E2_DIR_PIN 28`
			`#define E2_ENABLE_PIN 39`

			`#define LED_PIN 13`

Rename BEEPER to BEEPER_PIN For consistency with other pins, allowing use of `PIN_EXISTS` macro. 9 years ago			`#define FAN_PIN 7`
			`#define FAN1_PIN 8`
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion…. 10 years ago
			`#define PS_ON_PIN 45`
			`#define KILL_PIN 46`

Clean up RUMBA pins conditions 9 years ago			`#if TEMP_SENSOR_0 == 0`
Rename BEEPER to BEEPER_PIN For consistency with other pins, allowing use of `PIN_EXISTS` macro. 9 years ago			`#define TEMP_0_PIN -1`
			`#define HEATER_0_PIN -1`
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion…. 10 years ago			`#else`
Rename BEEPER to BEEPER_PIN For consistency with other pins, allowing use of `PIN_EXISTS` macro. 9 years ago			`#define HEATER_0_PIN 2 // EXTRUDER 1`
Clean up RUMBA pins conditions 9 years ago			`#if TEMP_SENSOR_0 == -1`
Rename BEEPER to BEEPER_PIN For consistency with other pins, allowing use of `PIN_EXISTS` macro. 9 years ago			`#define TEMP_0_PIN 6 // ANALOG NUMBERING - connector K1 on RUMBA thermocouple ADD ON is used`
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion…. 10 years ago			`#else`
			`#define TEMP_0_PIN 15 // ANALOG NUMBERING - default connector for thermistor T0 on rumba board is used`
			`#endif`
			`#endif`

Clean up RUMBA pins conditions 9 years ago			`#if TEMP_SENSOR_1 == 0`
Rename BEEPER to BEEPER_PIN For consistency with other pins, allowing use of `PIN_EXISTS` macro. 9 years ago			`#define TEMP_1_PIN -1`
			`#define HEATER_1_PIN -1`
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion…. 10 years ago			`#else`
Rename BEEPER to BEEPER_PIN For consistency with other pins, allowing use of `PIN_EXISTS` macro. 9 years ago			`#define HEATER_1_PIN 3 // EXTRUDER 2`
Clean up RUMBA pins conditions 9 years ago			`#if TEMP_SENSOR_1 == -1`
Rename BEEPER to BEEPER_PIN For consistency with other pins, allowing use of `PIN_EXISTS` macro. 9 years ago			`#define TEMP_1_PIN 5 // ANALOG NUMBERING - connector K2 on RUMBA thermocouple ADD ON is used`
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion…. 10 years ago			`#else`
			`#define TEMP_1_PIN 14 // ANALOG NUMBERING - default connector for thermistor T1 on rumba board is used`
			`#endif`
			`#endif`

Clean up RUMBA pins conditions 9 years ago			`#if TEMP_SENSOR_2 == 0`
Rename BEEPER to BEEPER_PIN For consistency with other pins, allowing use of `PIN_EXISTS` macro. 9 years ago			`#define TEMP_2_PIN -1`
			`#define HEATER_2_PIN -1`
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion…. 10 years ago			`#else`
Rename BEEPER to BEEPER_PIN For consistency with other pins, allowing use of `PIN_EXISTS` macro. 9 years ago			`#define HEATER_2_PIN 6 // EXTRUDER 3`
Clean up RUMBA pins conditions 9 years ago			`#if TEMP_SENSOR_2 == -1`
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion…. 10 years ago			`#define TEMP_2_PIN 7 // ANALOG NUMBERING - connector K3 on RUMBA thermocouple ADD ON is used <-- this can not be used when TEMP_SENSOR_BED is defined as thermocouple`
			`#else`
			`#define TEMP_2_PIN 13 // ANALOG NUMBERING - default connector for thermistor T2 on rumba board is used`
			`#endif`
			`#endif`

			`//optional for extruder 4 or chamber: #define TEMP_X_PIN 12 // ANALOG NUMBERING - default connector for thermistor T3 on rumba board is used`
			`//optional FAN1 can be used as 4th heater output: #define HEATER_3_PIN 8 // EXTRUDER 4`

Clean up RUMBA pins conditions 9 years ago			`#if TEMP_SENSOR_BED == 0`
Rename BEEPER to BEEPER_PIN For consistency with other pins, allowing use of `PIN_EXISTS` macro. 9 years ago			`#define TEMP_BED_PIN -1`
			`#define HEATER_BED_PIN -1`
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion…. 10 years ago			`#else`
Rename BEEPER to BEEPER_PIN For consistency with other pins, allowing use of `PIN_EXISTS` macro. 9 years ago			`#define HEATER_BED_PIN 9 // BED`
Clean up RUMBA pins conditions 9 years ago			`#if TEMP_SENSOR_BED == -1`
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion…. 10 years ago			`#define TEMP_BED_PIN 7 // ANALOG NUMBERING - connector K3 on RUMBA thermocouple ADD ON is used <-- this can not be used when TEMP_SENSOR_2 is defined as thermocouple`
			`#else`
Rename BEEPER to BEEPER_PIN For consistency with other pins, allowing use of `PIN_EXISTS` macro. 9 years ago			`#define TEMP_BED_PIN 11 // ANALOG NUMBERING - default connector for thermistor THB on rumba board is used`
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion…. 10 years ago			`#endif`
			`#endif`

			`#define SDPOWER -1`
			`#define SDSS 53`
SDCARDDETECT -> SD_DETECT, added docs - `SD_DETECT_PIN` replaces `SDCARDDETECT` - `SD_DETECT_INVERTED` replaces `SDCARDDETECTINVERTED` - Revise the description of `SD_DETECT_INVERTED` - Add a note about the override of `SD_DETECT_INVERTED` in `Conditionals.h` 9 years ago			`#define SD_DETECT_PIN 49`
Rename BEEPER to BEEPER_PIN For consistency with other pins, allowing use of `PIN_EXISTS` macro. 9 years ago			`#define BEEPER_PIN 44`
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion…. 10 years ago			`#define LCD_PINS_RS 19`
			`#define LCD_PINS_ENABLE 42`
			`#define LCD_PINS_D4 18`
			`#define LCD_PINS_D5 38`
			`#define LCD_PINS_D6 41`
			`#define LCD_PINS_D7 40`
			`#define BTN_EN1 11`
			`#define BTN_EN2 12`
			`#define BTN_ENC 43`
Update RUMBA pins file Add FAN1_PIN and SERVO0_PIN 10 years ago
			`#define SERVO0_PIN 5`