You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
111 lines
3.2 KiB
111 lines
3.2 KiB
4 years ago
|
/**
|
||
|
* Marlin 3D Printer Firmware
|
||
|
* Copyright (c) 2021 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||
|
*
|
||
|
* Based on Sprinter and grbl.
|
||
|
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
||
|
*
|
||
|
* This program is free software: you can redistribute it and/or modify
|
||
|
* it under the terms of the GNU General Public License as published by
|
||
|
* the Free Software Foundation, either version 3 of the License, or
|
||
|
* (at your option) any later version.
|
||
|
*
|
||
|
* This program is distributed in the hope that it will be useful,
|
||
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||
|
* GNU General Public License for more details.
|
||
|
*
|
||
|
* You should have received a copy of the GNU General Public License
|
||
|
* along with this program. If not, see <https://www.gnu.org/licenses/>.
|
||
|
*
|
||
|
*/
|
||
|
#pragma once
|
||
|
|
||
|
#ifndef BOARD_INFO_NAME
|
||
|
#define BOARD_INFO_NAME "FYSETC SPIDER"
|
||
|
#endif
|
||
|
#ifndef DEFAULT_MACHINE_NAME
|
||
|
#define DEFAULT_MACHINE_NAME BOARD_INFO_NAME
|
||
|
#endif
|
||
|
|
||
|
//
|
||
|
// EEPROM Emulation
|
||
|
//
|
||
|
#if NO_EEPROM_SELECTED
|
||
|
#undef NO_EEPROM_SELECTED
|
||
|
//#define FLASH_EEPROM_EMULATION
|
||
|
//#define SRAM_EEPROM_EMULATION
|
||
|
#define I2C_EEPROM
|
||
|
#endif
|
||
|
|
||
|
#if ENABLED(I2C_EEPROM)
|
||
|
#define MARLIN_EEPROM_SIZE 0x1000 // 4KB
|
||
|
#endif
|
||
|
|
||
|
//
|
||
|
// Steppers
|
||
|
//
|
||
|
#define X2_STEP_PIN PD12
|
||
|
#define X2_DIR_PIN PC4
|
||
|
#define X2_ENABLE_PIN PE8
|
||
|
#define X2_CS_PIN PA15
|
||
|
|
||
|
#define Z2_STEP_PIN PE1
|
||
|
#define Z2_DIR_PIN PE0
|
||
|
#define Z2_ENABLE_PIN PC5
|
||
|
#define Z2_CS_PIN PD11
|
||
|
|
||
|
//
|
||
|
// Heaters / Fans
|
||
|
//
|
||
|
#define HEATER_0_PIN PB15
|
||
|
#define HEATER_1_PIN PC8
|
||
|
#define HEATER_2_PIN PB3
|
||
|
#define HEATER_BED_PIN PB4
|
||
|
|
||
|
//
|
||
|
// Steppers
|
||
|
//
|
||
|
#define X_ENABLE_PIN PE9
|
||
|
|
||
|
#if HAS_TMC_UART
|
||
|
#define X_SERIAL_TX_PIN PE7
|
||
|
#define X_SERIAL_RX_PIN PE7
|
||
|
#define Y_SERIAL_TX_PIN PE15
|
||
|
#define Y_SERIAL_RX_PIN PE15
|
||
|
#define Z_SERIAL_TX_PIN PD10
|
||
|
#define Z_SERIAL_RX_PIN PD10
|
||
|
#define E0_SERIAL_TX_PIN PD7
|
||
|
#define E0_SERIAL_RX_PIN PD7
|
||
|
#define E1_SERIAL_TX_PIN PC14
|
||
|
#define E1_SERIAL_RX_PIN PC14
|
||
|
#define E2_SERIAL_TX_PIN PC15
|
||
|
#define E2_SERIAL_RX_PIN PC15
|
||
|
#define X2_SERIAL_TX_PIN PA15
|
||
|
#define X2_SERIAL_RX_PIN PA15
|
||
|
#define Z2_SERIAL_TX_PIN PD11
|
||
|
#define Z2_SERIAL_RX_PIN PD11
|
||
|
#endif
|
||
|
|
||
|
//
|
||
|
// Software SPI pins for TMC2130 stepper drivers
|
||
|
//
|
||
|
#define TMC_USE_SW_SPI
|
||
|
#if ENABLED(TMC_USE_SW_SPI)
|
||
|
#ifndef TMC_SW_MOSI
|
||
|
#define TMC_SW_MOSI PE14
|
||
|
#endif
|
||
|
#ifndef TMC_SW_MISO
|
||
|
#define TMC_SW_MISO PE13
|
||
|
#endif
|
||
|
#ifndef TMC_SW_SCK
|
||
|
#define TMC_SW_SCK PE12
|
||
|
#endif
|
||
|
#endif
|
||
|
|
||
|
#if HOTENDS > 3 || E_STEPPERS > 3
|
||
|
#error "FYSETC SPIDER supports up to 3 hotends / E-steppers."
|
||
|
#else
|
||
|
#include "pins_FYSETC_S6.h"
|
||
|
#endif
|